Surface texture processing for tribological performance improvement of UHMWPE-based water-lubricated bearings

Purpose Water-lubricated bearings can significantly reduce the pollution to environment because the traditional oil lubricant is replaced by water in the bearings. The ultrahigh molecular weight polyethylene (UHMWPE) has proven to be effective and reliable for the manufacturing of water-lubricated bearings. However, limited work has been done to address the improvement of the tribological performance of the UHMWPE-based water-lubricated bearings using surface texture processing. This paper aims to investigate the effects of bar-grooved surface on the tribological performance improvement of UHMWPE-based water-lubricated bearings. Design/methodology/approach For the first time, the bar grooves were processed on the surfaces of UHMWPE-based water-lubricated bearings. The CBZ-1 friction and wear tester have been used to test the wear and friction performance of the bearing samples. The LI laser interference surface contour graph and the digital microscope have been used to measure the surface morphology of the specimens. The tribological characteristics of the tested bearings were analyzed. Findings With bar grooves added on the surfaces of the specimens, the friction coefficient of the specimens were lower than that of the specimens without surface texture processing; the wear quantity of the two kinds of specimens were almost the same; by using the LI laser interference surface contour graph and the digital microscope to measure the surface morphology of the specimens, the furrows of the specimens with bar grooves were narrower and shallower than that of the specimens without bar grooves. Practical implications The paper implicates that the surface texture processing using bar grooves can reduce the friction coefficient and prolong the service life of the water-lubricated bearings in practical applications. Originality/value This paper fulfills an identified need to provide important theoretical and experimental support to the design of water-lubricated bearings in practical applications.

[1]  Yonghong Fu,et al.  The Influence of Partially Textured Slider with Oriented Parabolic Grooves on the Behavior of Hydrodynamic Lubrication , 2012 .

[2]  S. Chattopadhyaya,et al.  Characterization of Friction Surfaced Coatings of AISI 316 Tool over High-Speed-Steel Substrate , 2017 .

[3]  I. Etsion,et al.  Testing piston rings with partial laser surface texturing for friction reduction , 2006 .

[4]  Jun Hong,et al.  Effects of surface texture on the lubrication performance of the floating ring bearing , 2016 .

[5]  J. A. Walowit,et al.  A Theory of Lubrication by Microirregularities , 1966 .

[6]  Chandra B. Khatri,et al.  Influence of textured surface on the performance of non-recessed hybrid journal bearing operating with non-Newtonian lubricant , 2016 .

[7]  Roy L. Orndorff,et al.  WATER‐LUBRICATED RUBBER BEARINGS, HISTORY AND NEW DEVELOPMENTS , 1985 .

[8]  Ahmad Athif Mohd Faudzi,et al.  Design, characterization, and manufacturing of circular bellows pneumatic soft actuator , 2017 .

[9]  Grzegorz Krolczyk,et al.  Investigation on the edge forces in ball end milling of inclined surfaces , 2016 .

[10]  G. Królczyk,et al.  Chip Formation Zone Analysis During the Turning of Austenitic Stainless Steel 316L under MQCL Cooling Condition , 2016 .

[11]  Saeid Amini,et al.  Experimental study on effect of micro textured surfaces generated by ultrasonic vibration assisted face turning on friction and wear performance , 2016 .

[12]  Wojciech Litwin,et al.  Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research , 2014 .

[13]  J. Xing,et al.  A new rubber/UHMWPE alloy for water-lubricated stern bearings , 2015 .

[14]  L. Vitoux,et al.  The wear and lubrication performance of liquid–solid self-lubricated coatings , 2013 .

[15]  Michel Fillon,et al.  A numerical investigation of both thermal and texturing surface effects on the journal bearings static characteristics , 2015 .

[16]  P. Maspeyrot,et al.  Influence of surface texturing on the hydrodynamic performance of a thrust bearing operating in steady-state and transient lubrication regime , 2016 .

[17]  Wang Hao,et al.  Study on tribological and vibration performance of a new UHMWPE/graphite/NBR water lubricated bearing material , 2015 .

[18]  C. Papadopoulos,et al.  Computational Fluid Dynamics Thermohydrodynamic Analysis of Three-Dimensional Sector-Pad Thrust Bearings With Rectangular Dimples , 2014 .

[19]  Meng Hua,et al.  A mixed lubrication model for studying tribological behaviors of surface texturing , 2014 .

[20]  Wei Huang,et al.  The load carrying capacity of textured sliding bearings with elastic deformation , 2017 .

[21]  S. Chattopadhyaya,et al.  Improvement of surface integrity of Nimonic C 263 super alloy produced by WEDM through various post-processing techniques , 2017 .

[22]  Arash Golchin,et al.  Tribological behavior of carbon-filled PPS composites in water lubricated contacts , 2015 .

[23]  S. M. Hsu,et al.  A critical assessment of surface texturing for friction and wear improvement , 2017 .

[24]  Zhike Peng,et al.  Effect of surface waviness on the static performance of aerostatic journal bearings , 2016 .

[25]  Peng-yang Li,et al.  Study on tribological properties of multi-layer surface texture on Babbitt alloys surface , 2016 .

[26]  Wojciech Litwin,et al.  Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing , 2015 .

[27]  Stanislaw Legutko,et al.  The influence of the cooling conditions on the cutting tool wear and the chip formation mechanism , 2016 .