A Numerically Supported Investigation of the 3D Flow in Centrifugal Impellers: Part II — Secondary Flow Structure

The three-dimensional flow in centrifugal impellers is investigated on the basis of a detailed analysis of the results of numerical simulations. An in-depth validation has been performed, based on the computations of Krain's centrifugal compressor and a radial pump impeller, both with vaneless diffusers and detailed comparisons with available experimental data, discussed in Part I, provide high confidence in the numerical tools and results. The low energy, high loss 'wake' region results from a balance between various contributions to the secondary flows influenced by tip leakage flows and is not necessarily connected to 3D boundary layer separation. A quantitative evaluation of the different contributions to the streamwise vorticity is performed, identifying the main features influencing their intensity. The main contributions are: the passage vortices along the end walls due to the flow turning; a passage vortex generated by the Coriolis forces proportional to the local loading and mainly active in the radial parts of the impeller; blade surface vortices due to the meridional curvature. The analysis provides an explanation for the differences in wake position under different geometries and flow conditions. A secondary flow representation is derived from the calculated 3D flow field for the two geometries validated in Part I, and the identified flow features largely confirm the theoretical analysis.

[1]  H. Krain.  Swirling Impeller Flow , 1988 .

[2]  Shun Kang,et al.  Numerical Simulation of 3D Viscous Flow in a Linear Compressor Cascade With Tip Clearance , 1994 .

[3]  L. Langston,et al.  Three-Dimensional Flow Within a Turbine Cascade Passage , 1977 .

[4]  William N. Dawes.  Unsteady flows and loss production in centrifugal and axial compressor stages , 1994 .

[5]  P. Stow,et al.  Thermodynamics and Fluid Mechanics of Turbomachinery , 1985 .

[6]  I. Lindblad,et al.  The engineering of multiblock/multigrid software for Navier-Stokes flows on structured meshes , 1993 .

[7]  C. Hah,et al.  Secondary Flows and Vortex Motion in a High-Efficiency Backswept Impeller at Design and Off-Design Conditions , 1989 .

[8]  R. J. Goldstein,et al.  Convective Transport Phenomena on the Suction Surface of a Turbine Blade Including the Influence of Secondary Flows Near the Endwall , 1991 .

[9]  J. D. Denton,et al.  The Use of a Distributed Body Force to Simulate Viscous Effects in 3D Flow Calculations , 1986 .

[10]  Shimpei Mizuki,et al.  A Study on the Flow Mechanism Within Centrifugal Impeller Channels , 1975 .

[11]  H. E. Gallus,et al.  Three-Dimensional Separated Flow Field in the Endwall Region of an Annular Compressor Cascade in the Presence of Rotor-Stator Interaction: Part 1—Quasi-Steady Flow Field and Comparison With Steady-State Data , 1990 .

[12]  Mark W. Johnson,et al.  Secondary Flow Mixing Losses in a Centrifugal Impeller , 1983 .

[13]  D. Eckardt,et al.  Detailed Flow Investigations Within a High-Speed Centrifugal Compressor Impeller , 1976 .

[14]  C. Hah,et al.  Application of Viscous Flow Computations for the Aerodynamic Performance of a Backswept Impeller at Various Operating Conditions , 1988 .

[15]  R. Dean,et al.  Rotating Wakes in Vaneless Diffusers , 1960 .

[16]  R. Braembussche.  Description of secondary flows in radial flow machines , 1985 .

[17]  M. V. Casey,et al.  The Use of 3D Viscous Flow Calculations in the Design and Analysis of Industrial Centrifugal Compressors , 1992 .

[18]  Allan J. Acosta,et al.  An Experimental Study of Centrifugal-Pump Impellers , 1955 .