Sulfuric acid treatment of indium tin oxide for application of organic light-emitting diodes

In this paper, indium tin oxide (ITO) substrates were treated by ethanol, sulfuric acid (98%) and oxygen plasma respectively, based on which organic light-emitting diodes (OLEDs) with the same double-layer structure: ITO/N,N'-bis-(1-naphyl)-N,N'-diphenyl-1,1'- biphenyl-4,4'-diamine(NPB)/tris-(8-hydroxyquinoline) aluminum(Alq3)/ Mg:Ag/Al were fabricated. The morphology and compositions of differently treated ITO films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). AFM results showed that all these treatments didn't change much the average roughness of ITO films, while ethanol has little influence on the large "peak-valley" (P-V) distance of ITO film; ITO film treated by sulfuric acid has suitable surface morphology with low P-V distance, low average roughness and small particle radius. XPS analysis proved that ethanol has the weakest ability to remove carbon contamination on the surface of ITO film which resulted in unevenly distributed current and high barriers for hole injection; sulfuric-acid-treated ITO film has the least contamination of carbon and higher concentration of oxygen vacancies, both of which are helpful for the improvement of devices. In the condition of room temperature and atmosphere and without encapsulation, measurements of the current-voltage, brightness-voltage and lifetime characteristics of these devices were conducted and showed good agreement with what expected from the results of AFM and XPS analysis: the ethanol-treated ITO provides very unstable performance with low efficiency for the device based on it, while the device based on sulfuric-acid-treated ITO anode had even better performance at higher driven voltage (>7V) comparing with the device based on oxygen-plasma-treated ITO substrate and had the highest current-luminance efficiency (3.2 cd/A) and the longest lifetime (2 hours).

[1]  Shizuo Tokito,et al.  Improvement of organic electroluminescent device performance by in situ plasma treatment of indium–tin-oxide surface , 2000 .

[2]  W. R. Salaneck,et al.  Characterisation of the properties of surface-treated indium-tin oxide thin films , 1999 .

[3]  C. C. Wu,et al.  Surface modification of indium tin oxide by plasma treatment: An effective method to improve the efficiency, brightness, and reliability of organic light emitting devices , 1997 .

[4]  Franco Cacialli,et al.  Indium-tin oxide treatments for single- and double-layer polymeric light-emitting diodes: The relation between the anode physical, chemical, and morphological properties and the device performance , 1998 .

[5]  Hiroshi Morikawa,et al.  Crystallization and electrical property change on the annealing of amorphous indium-oxide and indium-tin-oxide thin films , 2000 .

[6]  K. H. Schulz,et al.  Electrical, optical and structural characteristics of indium-tin-oxide thin films deposited on glass and polymer substrates , 1997 .

[7]  P. Bohn,et al.  Effect of acidic and basic surface dipoles on the depletion layer of indium tin oxide as measured by in-plane conductance , 2004 .

[8]  A. ADoefaa,et al.  ? ? ? ? f ? ? ? ? ? , 2003 .

[9]  R. Egdell,et al.  High resolution x-ray photoemission study of plasma oxidation of indium–tin–oxide thin film surfaces , 2000 .

[10]  Junji Kido,et al.  Fabrication of highly efficient organic electroluminescent devices , 1998 .

[11]  Alberto Piqué,et al.  Indium tin oxide thin films for organic light-emitting devices , 1999 .

[12]  K. H. Schulz,et al.  Dependence of the sheet resistance of indium-tin-oxide thin films on grain size and grain orientation determined from X-ray diffraction techniques , 1999 .

[13]  Masamichi Fujihira,et al.  Fine tuning work function of indium tin oxide by surface molecular design: Enhanced hole injection in organic electroluminescent devices , 2001 .

[14]  R. Friend,et al.  Surface wetting properties of treated indium tin oxide anodes for polymer light-emitting diodes , 2000 .

[15]  C. Tang,et al.  Organic Electroluminescent Diodes , 1987 .

[16]  T. Nguyen,et al.  Thermal and chemical treatment of ITO substrates for improvement of OLED performance , 2003 .

[17]  Ying Wu,et al.  Surface treatment of indium tin oxide by oxygen-plasma for organic light-emitting diodes , 2003 .

[18]  S. Chua,et al.  An in situ sheet resistance study of oxidative-treated indium tin oxide substrates for organic light emitting display applications , 2002 .

[19]  John A. Rogers,et al.  Organic smart pixels , 1998 .

[20]  Y. Tak,et al.  Criteria for ITO (indium tin-oxide) thin film as the bottom electrode of an organic light emitting diode , 2002 .

[21]  Masanori Ozaki,et al.  Organic electroluminescent diodes as a light source for polymeric integrated devices , 2001, SPIE OPTO.