Surface integrity in cryogenic machining of nickel based alloy—Inconel 718

[1]  M. M. Barash,et al.  The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 1: Cutting With a Sharp Tool , 1976 .

[2]  J. Cohen,et al.  Residual Stress: Measurement by Diffraction and Interpretation , 1987 .

[3]  A. B. Chattopadhyay,et al.  A study of effects of cryo-cooling in grinding , 1995 .

[4]  T. Watkins,et al.  Surface residual stresses in machined austenitic stainless steel , 1996 .

[5]  A. Dias,et al.  Residual stress analysis in orthogonal machining of standard and resulfurized AISI 316L steels , 1999 .

[6]  Hossam A. Kishawy,et al.  Surface Integrity of Die Material in High Speed Hard Machining, Part 2: Microhardness Variations and Residual Stresses , 2000 .

[7]  J. L. Lebrun,et al.  MACHINING RESIDUAL STRESSES IN AISI 316L STEEL AND THEIR CORRELATION WITH THE CUTTING PARAMETERS , 2002 .

[8]  C. García-Rosales,et al.  Residual stresses in tool steel due to hard‐turning , 2003 .

[9]  José Outeiro,et al.  Experimental Assessment of Temperature Distribution in Three-Dimensional Cutting Process , 2004 .

[10]  Toshiyuki Obikawa,et al.  Prediction model of surface residual stress within a machined surface by combining two orthogonal plane models , 2004 .

[11]  M. A. Mannan,et al.  Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools , 2004 .

[12]  M. A. Mannan,et al.  Surface integrity when machining age hardened Inconel 718 with coated carbide cutting tools , 2004 .

[13]  Fukuo Hashimoto,et al.  Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer + hone cutting edge geometry , 2005 .

[14]  Philip J. Withers,et al.  Turning of advanced Ni based alloys obtained via powder metallurgy route , 2006 .

[15]  Keith Ridgway,et al.  An analysis of the residual stresses generated in Inconel 718™ when turning , 2006 .

[16]  N. Fredj,et al.  Ground surface improvement of the austenitic stainless steel AISI 304 using cryogenic cooling , 2006 .

[17]  M. Preuss,et al.  Characterisation of Residual Stresses in Machined Surfaces of a High Strength Nickel-Base Superalloy , 2006 .

[18]  S. Y. Liang,et al.  Residual Stress Modeling in Orthogonal Machining , 2007 .

[19]  Tuğrul Özel,et al.  Finite element modeling the influence of edge roundness on the stress and temperature fields induced by high-speed machining , 2007 .

[20]  I. S. Jawahir,et al.  Analysis of residual stresses induced by dry turning of difficult-to-machine materials , 2008 .

[21]  Heat treatment and fine-blanking Inconel 718 , 2008 .

[22]  Philip J. Withers,et al.  Residual stresses in face finish turning of high strength nickel-based superalloy , 2009 .

[23]  Peter Krajnik,et al.  Transitioning to sustainable production – Part I: application on machining technologies , 2010 .