Investigation of the role of cavity airflow on the performance of building-integrated photovoltaic panels

Abstract Building-integrated photovoltaic (BIPV) panels are emerging as a useful technology for helping to achieve net-zero energy buildings. At this time, the main drawback with BIPV systems is the cost per kilowatt per hour of electricity generated. Besides cheaper production of photovoltaic panels, increases in their efficiency can be obtained by reducing panel temperatures. This is often achieved by adding a cavity beneath the panels to allow ventilation of the rear of the panel. However, the details of airflow in the cavity and the effect on cooling have not been rigorously researched. Life-time enhancement against degradation is also an effective technique to reduce the cost of electricity generated. Moisture ingress and thermal stresses are among the primary reasons for degradation of BIPVs; these processes are directly affected by air and moisture flow around the panels. The surface temperature thermography and airflow observations performed in this work helps to understand the transport mechanisms above and below the panels. For this purpose, a novel setup was developed consisting of a building model with a mock BIPV panel plus a solar simulator placed inside an atmospheric wind tunnel. Particle image velocimetry (PIV) and infra-red thermography were performed to simultaneously monitor the surface temperature and airflow above and below the panel. The study clearly shows how the accelerated airflow within the cavity increases the heat exchange between the PV and airflow and consequently reduces the PV temperature. It is also shown that the stepped open arrangement of panels is more effective in reducing the temperature comparing to a flat arrangement. This arrangement also has a better resistant against the air and moisture ingress.

[1]  Tin-Tai Chow,et al.  A Review on Photovoltaic/Thermal Hybrid Solar Technology , 2010, Renewable Energy.

[2]  Bjørn Petter Jelle,et al.  Building integrated photovoltaic products: A state-of-the-art review and future research opportunities , 2012 .

[3]  Adam Scherba,et al.  Modeling impacts of roof reflectivity, integrated photovoltaic panels and green roof systems on sensible heat flux into the urban environment , 2011 .

[4]  Nasrudin Abd Rahim,et al.  A review on global solar energy policy , 2011 .

[5]  Dennis L. Loveday,et al.  Equilibrium thermal characteristics of a building integrated photovoltaic tiled roof , 2009 .

[6]  K. Sumathy,et al.  Photovoltaic thermal module concepts and their performance analysis: A review , 2010 .

[7]  Ranko Goic,et al.  review of solar photovoltaic technologies , 2011 .

[8]  Rattanasuda Naewngerndee,et al.  Finite element method for computational fluid dynamics to design photovoltaic thermal (PV/T) system configuration , 2011 .

[9]  M. Kempe.  Modeling of rates of moisture ingress into photovoltaic modules , 2006 .

[10]  Herricos Stapountzis,et al.  Flow and heat transfer inside a PV/T collector for building application , 2012 .

[11]  Marc A. Rosen,et al.  A critical review of photovoltaic–thermal solar collectors for air heating , 2011 .

[12]  Jan Kleissl,et al.  Effects of solar photovoltaic panels on roof heat transfer , 2010 .

[13]  Cristina Sanjuan,et al.  Experimental analysis of natural convection in open joint ventilated faades with 2D PIV , 2011 .

[14]  Mats Sandberg,et al.  Flow and heat transfer in the air gap behind photovoltaic panels , 1998 .

[15]  Zhiqiang John Zhai,et al.  Experimental and numerical investigation on thermal and electrical performance of a building integrated photovoltaic–thermal collector system , 2010 .

[16]  Luis Pérez-Lombard,et al.  A review on buildings energy consumption information , 2008 .

[17]  F. Haghighat,et al.  Approaches to study Urban Heat Island – Abilities and limitations , 2010 .

[18]  H. Manz,et al.  Available remodeling simulation for a BIPV as a shading device , 2011 .

[19]  E. E. van Dyk,et al.  Investigation of delamination in an edge-defined film-fed growth photovoltaic module , 2005 .

[20]  Mats Sandberg,et al.  Design procedure for cooling ducts to minimise efficiency loss due to temperature rise in PV arrays , 2006 .

[21]  F. Corvaro,et al.  Experimental PIV and interferometric analysis of natural convection in a square enclosure with partially active hot and cold walls , 2011 .

[22]  Manosh C. Paul,et al.  Effect of mounting geometry on convection occurring under a photovoltaic panel and the corresponding efficiency using CFD , 2011 .

[23]  Guohui Gan,et al.  Effect of air gap on the performance of building-integrated photovoltaics , 2009 .

[24]  Parham A. Mirzaei,et al.  Influence of the underneath cavity on buoyant-forced cooling of the integrated photovoltaic panels in building roof: a thermography study , 2015 .