Realization of a micro pressure sensor with high sensitivity and overload by introducing beams and Islands

Presented is a piezoresistive absolute micro pressure sensor for altimetry. This investigation involves the design, fabrication and testing of the sensor. By analyzing the stress distribution of sensitive elements using finite element method (FEM), an improved structure is built up through introducing multi islands and sensitive beams into traditional flat diaphragm. The proposed configuration presents its advantages in terms of enhanced sensitivity and overload resistance compared with the bossed diaphragm and flat diaphragm structures. Multivariate fittings based on ANSYS® simulation results are performed to establish equations about surface stress and deflection of the sensor. Optimization by MATLAB® is carried out to determine the structure dimensions. Silicon bulk micromachining technology is utilized to fabricate the sensor prototype, and the fabrication process is discussed. The output signals under both static and dynamic conditions are evaluated and tested. Experimental results demonstrate the sensor features a relatively high sensitivity of 17.795 μV/V/Pa in the operating range of 500 Pa at room temperature and a proper overload resistance of 200 times overpressure to promise its survival under atmosphere. The favorable performances enable the sensor’s application in measuring absolute micro pressure.

[1]  Wang Yan,et al.  Micromachined beam-diaphragm structure improves performances of pressure transducer , 1990 .

[2]  Ha-Duong Ngo,et al.  Design and simulation of ultra high sensitive piezoresistive MEMS sensor with structured membrane for low pressure applications , 2010, 2010 12th Electronics Packaging Technology Conference.

[3]  Liwei Lin,et al.  A simulation program for the sensitivity and linearity of piezoresistive pressure sensors , 1999 .

[4]  Chang Liu,et al.  Foundations of MEMS , 2006 .

[5]  Chie Gau,et al.  Micro pressure sensor fabrication without problem of stiction for a wider range of measurement , 2004, Proceedings of IEEE Sensors, 2004..

[6]  Zhuangde Jiang,et al.  Surface stress-induced deflection of a microcantilever with various widths and overall microcantilever sensitivity enhancement via geometry modification , 2011 .

[7]  Akio Yasukawa,et al.  A special silicon diaphragm pressure sensor with high output and high accuracy , 1981 .

[8]  Ralph H. Johnson,et al.  A high-sensitivity ribbed and bossed pressure transducer , 1992 .

[9]  T. Kenny,et al.  What is the Young's Modulus of Silicon? , 2010, Journal of Microelectromechanical Systems.

[10]  O. N. Tufte,et al.  Piezoresistive Properties of Silicon Diffused Layers , 1963 .

[11]  Ding Jianning,et al.  Fabrication and temperature coefficient compensation technology of low cost high temperature pressure sensor , 2005 .

[12]  Ernst Obermeier,et al.  AeroMEMS sensor array for high-resolution wall pressure measurements , 2006 .

[13]  S. Timoshenko,et al.  THEORY OF PLATES AND SHELLS , 1959 .

[14]  Zhuangde Jiang,et al.  The design and analysis of beam-membrane structure sensors for micro-pressure measurement. , 2012, The Review of scientific instruments.

[15]  K. Wise,et al.  Pressure sensitivity in anisotropically etched thin-diaphragm pressure sensors , 1979, IEEE Transactions on Electron Devices.

[16]  James H. Smith,et al.  Micromachined pressure sensors: review and recent developments , 1997 .

[17]  Thomas W. Kenny,et al.  Packaging a piezoresistive pressure sensor to measure low absolute pressures over a wide sub-zero temperature range , 2000 .

[18]  Jiachou Wang,et al.  A High-Performance Dual-Cantilever High-Shock Accelerometer Single-Sided Micromachined in (111) Silicon Wafers , 2010, Journal of Microelectromechanical Systems.

[19]  Beth L. Pruitt,et al.  Review: Semiconductor Piezoresistance for Microsystems , 2009, Proceedings of the IEEE.