Environmental friendly crush-magnetic separation technology for recycling metal-plated plastics from end-of-life vehicles.

Metal-plated plastics (MPP), which are important from the standpoint of aesthetics or even performance, are increasingly employed in a wide variety of situations in the automotive industry. Serious environmental problems will be caused if they are not treated appropriately. Therefore, recycling of MPP is an important subject not only for resource recycling but also for environmental protection. This work represents a novel attempt to deal with the MPP. A self-designed hammer crusher was used to liberate coatings from the plastic substrate. The size distribution of particles was analyzed and described by the Rosin-Rammler function model. The optimum retaining time of materials in the crusher is 3 min. By this time, the liberation rate of the materials can reach 87.3%. When the density of the suspension is 31,250 g/m(3), the performance of liberation is the best. Two-step magnetic separation was adopted to avoid excessive crushing and to guarantee the quality of products. Concerning both the separation efficiency and grade of products, the optimum rotational speed of the magnetic separator is 50-70 rpm. On the basis of the above studies about the liberating and separating behavior of the materials, a continuous recycling system (the technology of crush-magnetic separation) is developed. This recycling system provides a feasible method for recycling MPP efficiently, economically, and environmentally.

[1]  Peter Erskine Wells,et al.  The Automobile Industry & Sustainability , 2007 .

[2]  Wang Xiang,et al.  Implementing extended producer responsibility: vehicle remanufacturing in China , 2011 .

[3]  Liu Zhong-wei.  Research Progress on the Domestic Recycling Method of ABS Plastic Electro-plating , 2010 .

[4]  J. Mcauley.  Global sustainability and key needs in future automotive design. , 2003, Environmental science & technology.

[5]  P. H. Shipway,et al.  Removal of coatings from polymer substrates by solid particle blasting to enhance reuse or recycling , 2007 .

[6]  Heather L MacLean,et al.  Life cycle assessment of automobile/fuel options. , 2003, Environmental science & technology.

[7]  Zhenming Xu,et al.  A novel process for recovering valuable metals from waste nickel-cadmium batteries. , 2009, Environmental science & technology.

[8]  S. Vidyasagar,et al.  Classification of metals and plastics from printed circuit boards (PCB) using air classifier , 2008 .

[9]  Eric Forssberg,et al.  Mechanical separation-oriented characterization of electronic scrap , 1997 .

[10]  Chul-Hyun Park,et al.  Application of electrostatic separation to the recycling of plastic wastes: separation of PVC, PET, and ABS. , 2008, Environmental science & technology.

[11]  Zhenming Xu,et al.  An environmental friendly recovery production line of waste toner cartridges. , 2011, Journal of hazardous materials.

[12]  H. Akiyama,et al.  Recycle of Metal-Plating on Plastics by Pulse Arc Discharges , 2007, 2007 IEEE 34th International Conference on Plasma Science (ICOPS).

[13]  Jing Feng He,et al.  Research on Liberation Mechanism of the Impact Crushing Waste Printed Circuit Board , 2010 .

[14]  Nizar Haoues,et al.  State of the art of plastic sorting and recycling : Feedback to vehicle design , 2007 .

[15]  J.H.P. Watson,et al.  Superconducting discs as permanent magnets for magnetic separation , 1998 .

[16]  J Van Caneghem,et al.  Automotive shredder residue (ASR): reviewing its production from end-of-life vehicles (ELVs) and its recycling, energy or chemicals' valorisation. , 2011, Journal of hazardous materials.

[17]  Xu Zhen-ming.  Pulverization Characteristics and Pulverizing of Waste Printed Circuit Boards(Printed Wiring Boards) Based on Resource Utilization , 2007 .