Role of Tip-Leakage Vortices and Passage Shock in Stall Inception in a Swept Transonic Compressor Rotor

The current paper reports on investigations aimed at advancing the understanding of the flow field near the casing of a forward-swept transonic compressor rotor. The role of tip clearance flow and its interaction with the passage shock on stall inception are analyzed in detail. Steady and unsteady three-dimensional viscous flow calculations are applied to obtain flow fields at various operating conditions. The numerical results are first compared with available measured data. Then, the numerically obtained flow fields are interrogated to identify the roles of flow interactions between the tip clearance flow, the passage shock, and the blade/endwall boundary layers. In addition to the flow field with nominal tip clearance, two more flow fields are analyzed in order to identify the mechanisms of blockage generation: one with zero tip clearance, and one with nominal tip clearance on the forward portion of the blade and zero clearance on the aft portion. The current study shows that the tip clearance vortex does not break down, even when the rotor operates in a stalled condition. Interaction between the shock and the suction surface boundary layer causes the shock, and therefore the tip clearance vortex, to oscillate. However, for the currently investigated transonic compressor rotor, so-called breakdown of the tip clearance vortex does not occur during stall inception. The tip clearance vortex originates near the leading edge tip, but moves downward in the spanwise direction inside the blade passage. A low momentum region develops above the tip clearance vortex from flow originating from the casing boundary layer. The low momentum area builds up immediately downstream of the passage shock and above the core vortex. This area migrates toward the pressure side of the blade passage as the flow rate is decreased. The low momentum area prevents incoming flow from passing through the pressure side of the passage and initiates stall inception. It is well known that inviscid effects dominate tip clearance flow. However, complex viscous flow structures develop inside the casing boundary layer at operating conditions near stall.Copyright © 2004 by ASME

[1]  Aspi Rustom Wadia,et al.  Low Aspect Ratio Transonic Rotors: Part 1—Baseline Design and Performance , 1993 .

[2]  Rodrick V. Chima,et al.  Calculation of Tip Clearance Effects in a Transonic Compressor Rotor , 1998 .

[3]  S. L. Puterbaugh,et al.  Control of Shock Structure and Secondary Flow Field Inside Transonic Compressor Rotors Through Aerodynamic Sweep , 1998 .

[4]  Aspi Rustom Wadia,et al.  Low Aspect Ratio Transonic Rotors: Part 2—Influence of Location of Maximum Thickness on Transonic Compressor Performance , 1993 .

[5]  C.Hah,et al.  Role of Tip clearance Flows on Flow Instability in Axial Flow Compressors , 2001 .

[6]  C. Hah,et al.  Three-Dimensional Flowfields Inside a Transonic Compressor With Swept Blades , 1990 .

[7]  C. Hah,et al.  Development of Hub Corner Stall and Its Influence on the Performance of Axial Compressor Blade Rows , 1999 .

[8]  Michael D. Hathaway,et al.  Recommendations for Achieving Accurate Numerical Simulation of Tip Clearance Flows in Transonic Compressor Rotors , 2000 .

[9]  Michael Lötzerich,et al.  Breakdown of Tip Leakage Vortices in Compressors at Flow Conditions Close to Stall , 1997 .

[10]  Edward M. Greitzer,et al.  The Role of Tip Clearance in High-Speed Fan Stall , 1991 .

[11]  Steven L. Puterbaugh,et al.  A Three-Dimensional Model for the Prediction of Shock Losses in Compressor Blade Rows , 1983 .

[12]  S. L. Puterbaugh,et al.  Unsteady Flow and Shock Motion in a Transonic Compressor Rotor , 1997 .

[13]  Ken-ichi Funazaki,et al.  Numerical Analysis of Tip Leakage Flow Field in a Transonic Axial Compressor Rotor , 2006 .

[14]  Aspi Rustom Wadia,et al.  The Effect of Tip Clearance on a Swept Transonic Compressor Rotor , 1996 .

[15]  E. Krause,et al.  Interaction between Longitudinal Vortices and Normal and Oblique Shocks , 2005 .

[16]  C. Hah,et al.  Application of Casing Circumferential Grooves for Improved Stall Margin in a Transonic Axial Compressor , 2002 .

[17]  W. C. Zierke,et al.  The High Reynolds Number Flow Through an Axial-Flow Pump , 1993 .

[18]  Mark L. Celestina,et al.  Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor , 1994 .

[19]  Aspi Rustom Wadia,et al.  Inner Workings of Aerodynamic Sweep , 1997 .