Effect of Substrate Roughness and Contact Scale on the Tribological Performance of MoS2 Coatings

This present study aimed to clarify the effect of contact scale and surface topography of substrates with different roughnesses on the actual contact area, tangential stiffness, and tangential deformation of the substrate at micro- and macro-scales via finite element method (FEM) simulations, as well as the final tribological performances of MoS2 coatings by experiments. The MoS2 coatings were deposited on stainless steel (SS) substrates with different roughnesses, and the settings in the simulation models were based on the roughness of the SS substrates. The predicted tribological behavior of the simulation results was confirmed by the morphological and compositional analysis of the wear track using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), 3D profilometer, and Raman spectroscopy. The results showed that the substrate with a surface roughness of Ra 600 nm (R600), coated by MoS2 nanosheets, exhibited excellent tribological properties at both micro- and macro-scales. At the micro-scale, the lubrication lifetime of R600 was as long as 930 cycles, while the substrates with surface roughnesses of Ra 60 nm (R60) and Ra 6 nm (R6) had a lubrication lifetime of 290 cycles and 47 cycles, respectively. At the macro-scale, the lifetime of the substrate R600 was 9509 cycles, which was nearly six times longer than the 1616 cycles of substrate R60. For the rough surface of substrate, the surface grooves could not only effectively preserve the lubricant but also continuously release them, ensuring that the lubricants with low shear strength were always present in the contact interface. It was further verified that the high surface roughness of the substrate reduced friction and wear by reducing the actual contact area and enhancing the tangential stiffness of asperities, thereby prolonging the lubrication lifetime. The wear mechanisms were discussed in terms of the morphology and chemical composition of the wear tracks.

[1]  Faqiang Li,et al.  Effect of Two Graphene Coatings on the Friction and Wear of Sliding Electrical Contact Interface , 2022, Lubricants.

[2]  Peidong Xue,et al.  Effect of Substrate Roughness on the Friction and Wear Behaviors of Laser-Induced Graphene Film , 2022, Lubricants.

[3]  He Huang,et al.  Experimental Investigation on Synergetic Effects of Micro Grooves and WSe2 in Sliding Contact , 2022, Lubricants.

[4]  V. Presser,et al.  Influence of structural depth of laser-patterned steel surfaces on the solid lubricity of carbon nanoparticle coatings , 2022, Friction.

[5]  S. Wartzack,et al.  Edge Pressures Obtained Using FEM and Half-Space: A Study of Truncated Contact Ellipses , 2022, Lubricants.

[6]  Shu Liu,et al.  Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact , 2022, Lubricants.

[7]  Wei-min Liu,et al.  Tribochemical reaction and wear mechanism of MoDTC based friction modifier , 2022, Tribology International.

[8]  Kun Liu,et al.  The unrecognized importance of roughness directionality to polymer wear , 2021 .

[9]  S. Tremmel,et al.  Understanding Friction in Cam–Tappet Contacts—An Application-Oriented Time-Dependent Simulation Approach Considering Surface Asperities and Edge Effects , 2021, Lubricants.

[10]  M. Suvanto,et al.  Reduced sliding friction on flat and microstructured metal injection molded (MIM) WC-Co hard metals with MoS2 composite lubricants , 2021 .

[11]  S. Ramakrishna,et al.  Tribological behavior of femtosecond laser-textured leaded brass , 2021 .

[12]  Shusheng Xu,et al.  Understanding of the lubrication mechanism of reduced graphene oxide coating via dual in-situ monitoring of the chemical and topographic structural evolution , 2021 .

[13]  A. Rosenkranz,et al.  Synergetic effects of surface texturing and solid lubricants to tailor friction and wear – A review , 2021, Tribology International.

[14]  Yadong Zhang,et al.  Enhanced anticorrosion and antiwear properties of Ti–6Al–4V alloys with laser texture and graphene oxide coatings , 2020 .

[15]  Lei Chen,et al.  Toward Robust Macroscale Superlubricity on Engineering Steel Substrate , 2020, Advanced materials.

[16]  Francisco Profito,et al.  Multi-Scale Surface Texturing in Tribology—Current Knowledge and Future Perspectives , 2019, Lubricants.

[17]  J. Ramkumar,et al.  Single step laser surface texturing for enhancing contact angle and tribological properties , 2019 .

[18]  M. Arenas,et al.  Tribological behaviour of laser textured Ti6Al4V alloy coated with MoS2 and graphene , 2018, Tribology International.

[19]  Dirk J. Schipper,et al.  The Influence of Surface Texturing on the Frictional Behaviour of Parallel Sliding Lubricated Surfaces under Conditions of Mixed Lubrication , 2018, Lubricants.

[20]  P. Shipway,et al.  Effects of surface roughness on local friction and temperature distributions in a steel-on-steel fretting contact , 2018 .

[21]  F. Mücklich,et al.  Influence of Surface Roughness on the Lubrication Effect of Carbon Nanoparticle-Coated Steel Surfaces , 2018, Tribology Letters.

[22]  Daniel Braun,et al.  Laser Textured Surfaces for Mixed Lubrication: Influence of Aspect Ratio, Textured Area and Dimple Arrangement , 2017 .

[23]  F. Mücklich,et al.  Long-lasting solid lubrication by CNT-coated patterned surfaces , 2017, Scientific Reports.

[24]  Jianxin Deng,et al.  Effect of laser surface textures combined with multi-solid lubricant coatings on the tribological properties of Al2O3/TiC ceramic , 2015 .

[25]  Farshid Sadeghi,et al.  A novel approach to model effects of surface roughness parameters on wear , 2015 .

[26]  Carsten Gachot,et al.  Oil film lifetime and wear particle analysis of laser-patterned stainless steel surfaces , 2015 .

[27]  Samir Aouadi,et al.  Textured VN coatings with Ag3VO4 solid lubricant reservoirs , 2011 .

[28]  Jože Vižintin,et al.  Finite element analysis of textured surfaces under reciprocating sliding , 2011 .

[29]  Akira Kohyama,et al.  Effect of geometrical parameters in micro-grooved crosshatch pattern under lubricated sliding friction , 2010 .

[30]  H. Zahouani,et al.  Effect of roughness scale on contact stiffness between solids , 2009 .

[31]  Izhak Etsion,et al.  Friction and wear of MoS2 films on laser textured steel surfaces , 2008 .

[32]  Farshid Sadeghi,et al.  Modeling of fretting wear evolution in rough circular contacts in partial slip , 2007 .

[33]  Mark O. Robbins,et al.  Finite element modeling of elasto-plastic contact between rough surfaces , 2005 .

[34]  Ali Erdemir,et al.  Review of engineered tribological interfaces for improved boundary lubrication , 2005 .

[35]  Ali Erdemir,et al.  Historical developments and new trends in tribological and solid lubricant coatings. , 2004 .

[36]  Marina Ruths,et al.  Frictional Forces and Amontons' Law: From the Molecular to the Macroscopic Scale , 2004 .

[37]  Staffan Jacobson,et al.  Influence of surface texture on boundary lubricated sliding contacts , 2003 .

[38]  Stefan Björklund,et al.  A finite element-based model of normal contact between rough surfaces , 2003 .

[39]  M. R. Douglass,et al.  A MEMS-based projection display , 1998, Proc. IEEE.

[40]  Kyriakos Komvopoulos,et al.  Elastic Finite Element Analysis of Multi-Asperity Contacts , 1992 .

[41]  H. A. Sherif,et al.  Relationship between normal and tangential contact stiffness of nominally flat surfaces , 1991 .

[42]  J. Greenwood,et al.  Contact of nominally flat surfaces , 1966, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[43]  J. Archard.  Contact and Rubbing of Flat Surfaces , 1953 .

[44]  A. Albers,et al.  Influence of flattening of rough surface profiles on the friction behaviour of mixed lubricated contacts , 2016 .

[45]  S. Prasad,et al.  Solid lubricants: a review , 2012, Journal of Materials Science.