Mathematical modelling and multi-response optimisation using response surface methodology and grey based Taguchi method: an experimental investigation

The present study deals with the application of full factorial design of experiment and response surface methodology in developing mathematical model considering input variables, i.e., cutting speed, feed and depth of cut for flank wear and surface roughness when hard turning AISI 4340 steel (HRC 47±1) using multilayer coated carbide insert (TiN/TiCN/Al2O3/ZrCN) under dry environment. Mathematical model output concluded that the RSM models proposed are statistically significant and adequate because of higher R2 value. It shows the high correlation between the experimental and predicted values. From ANOVA table, it is evident that, feed is the significant factor affecting surface roughness followed by cutting speed. Depth of cut is found to be insignificant from the studied range. For flank wear, cutting speed is the most significant factor followed by depth of cut. Feed is found to be insignificant for flank wear. The improvement of grey relational grade from initial parameter combination (d2-f3-v4) to the optimal parameter combination (d4-f1-v3) is found to be 0.4645 and is improved through the approach of Taguchi method with grey relational analysis to optimise the process parameter for multiple performances (surface roughness and flank wear).

[1]  Y. Sahin,et al.  Comparison of tool life between ceramic and cubic boron nitride (CBN) cutting tools when machining hardened steels , 2009 .

[2]  A. E. Diniz,et al.  Performance of coated, cemented carbide, mixed-ceramic and PCBN-H tools when turning W320 steel , 2009 .

[3]  Ramón Quiza,et al.  Comparing statistical models and artificial neural networks on predicting the tool wear in hard machining D2 AISI steel , 2008 .

[4]  C. L. Lin,et al.  Use of the Taguchi Method and Grey Relational Analysis to Optimize Turning Operations with Multiple Performance Characteristics , 2004 .

[5]  Anirban Bhattacharya,et al.  Estimating the effect of cutting parameters on surface finish and power consumption during high speed machining of AISI 1045 steel using Taguchi design and ANOVA , 2009, Prod. Eng..

[6]  Hari Singh,et al.  Optimizing power consumption for CNC turned parts using response surface methodology and Taguchi's technique—A comparative analysis , 2008 .

[7]  Ming-Chang Jeng,et al.  Optimization of turning operations with multiple performance characteristics using the Taguchi method and Grey relational analysis , 2009 .

[8]  J. Ferreira,et al.  A multivariate hybrid approach applied to AISI 52100 hardened steel turning optimization , 2007 .

[9]  J. Horng,et al.  Investigating the machinability evaluation of Hadfield steel in the hard turning with Al2O3/TiC mixed ceramic tool based on the response surface methodology , 2008 .

[10]  D. I. Lalwani,et al.  Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel , 2008 .

[11]  Hari Singh,et al.  Mathematical models of tool life and surface roughness for turning operation through response surface methodology , 2007 .

[12]  Tuğrul Özel,et al.  Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks , 2005 .

[13]  Hari Singh,et al.  Optimizing feed force for turned parts through the Taguchi technique , 2006 .

[14]  Abdulrahman Al-Ahmari,et al.  Predictive machinability models for a selected hard material in turning operations , 2007 .

[15]  Ali Riza Motorcu,et al.  Surface roughness model in machining hardened steel with cubic boron nitride cutting tool , 2008 .

[16]  V. C. Venkatesh,et al.  Performance evaluation of cemented carbide tools in turning AISI 1010 steel , 2001 .

[17]  Safian Sharif,et al.  Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools , 2007 .

[18]  A. Haq,et al.  Multi response optimization of machining parameters of drilling Al/SiC metal matrix composite using grey relational analysis in the Taguchi method , 2008 .

[19]  P. V. Rao,et al.  A surface roughness prediction model for hard turning process , 2007 .

[20]  Che Hassan Che Haron,et al.  Wear of coated and uncoated carbides in turning tool steel , 2001 .

[21]  J. Paulo Davim,et al.  Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts , 2009 .

[22]  Dilbag Singh,et al.  Optimization of Tool Geometry and Cutting Parameters for Hard Turning , 2007 .

[23]  J. Paulo Davim,et al.  Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts , 2007 .

[24]  Wen-Tung Chien,et al.  The investigation on the prediction of tool wear and the determination of optimum cutting conditions in machining 17-4PH stainless steel , 2003 .

[25]  Young-Woo Park,et al.  Tool Material Dependence of Hard Turning on The Surface Quality , 2002 .

[26]  Hari Singh,et al.  Multicharacteristic optimisation of CNC turned parts using principal component analysis , 2008 .