Influencing factor analysis of shale micro-indentation measurement

Abstract To address the difficulty in measuring mechanical properties within the reservoir formation during the process of drilling in shale formations, micro-indentation measurement technology is performed to determine the micro elastic modulus and the indentation hardness of a shale outcrop in the Longmaxi Formation in the Sichuan Basin (the Changning Area). Additionally, factors influencing the micro-indentation measurement are analyzed from aspects such as indenter defects, experimental parameter settings, shale surface properties, and shale composition. The results show that the elastic modulus and indentation hardness decrease with increasing indentation depth. The test is less affected by indenter passivation. The area function needs to be calibrated when the tip radius of the indenter is more than 10 μm. It is observed that the test is substantially influenced by the parameter settings, so reasonable parameters should be determined before conducting the test. The Oliver-Pharr method is applicable to shale outcrops of the Longmaxi Formation, which meet the general requirements of the method. The measured values increase with increasing packing density. Moreover, the fitting percentage of the unloading curve has an impact on the result, and the reasonable fitting percentage of the unloading curve for shale samples was determined to be from 45% to 75%.

[1]  Huang Jinliang.  Reservoir characteristics of shale gas in Longmaxi Formation of the Lower Silurian,southern Sichuan , 2012 .

[2]  Taihua Zhang,et al.  Influence of indenter tip roundness on hardness behavior in nanoindentation , 2007 .

[3]  Yang-Tse Cheng,et al.  Scaling approach to conical indentation in elastic-plastic solids with work hardening , 1998 .

[4]  A. Zehnder,et al.  Dependence of Micro-Mechanical Properties on Lithofacies: Indentation Experiments on Marcellus Shale , 2014 .

[5]  F. Ulm,et al.  The nanogranular nature of C–S–H , 2007 .

[6]  Carl H. Sondergeld,et al.  Nano to Macro Mechanical Characterization of Shale , 2012 .

[7]  George M. Pharr,et al.  On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation , 1992 .

[8]  Taihua Zhang,et al.  Experimental Verification And Theoretical Analysis Of The Relationships Between Hardness, Elastic Modulus, And The Work Of Indentation , 2008 .

[9]  G. Pharr,et al.  Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology , 2004 .

[10]  J. A. Ortega,et al.  Strength Homogenization of Double-Porosity Cohesive-Frictional Solids , 2013 .

[11]  Franz-Josef Ulm,et al.  Statistical indentation techniques for hydrated nanocomposites: concrete, bone, and shale , 2007 .

[12]  Franz-Josef Ulm,et al.  The effect of the nanogranular nature of shale on their poroelastic behavior , 2007 .

[13]  Keshra Sangwal,et al.  On the reverse indentation size effect and microhardness measurement of solids , 2000 .

[14]  H. Jennings,et al.  Does microstructure matter for statistical nanoindentation techniques , 2010 .

[15]  Gilles Chanvillard,et al.  Modelling Elasticity of a Hydrating Cement Paste , 2007 .

[16]  J. Sherwood,et al.  LETTER TO THE EDITOR: Packing of spheroids in three-dimensional space by random sequential addition , 1997 .

[17]  Michael V. Swain,et al.  Geometry and bluntness tip effects on elastic–plastic behaviour during nanoindentation of fused silica: experimental and FE simulation , 2010 .

[18]  Franz-Josef Ulm,et al.  The nanogranular origin of friction and cohesion in shale—A strength homogenization approach to interpretation of nanoindentation results , 2011 .

[19]  Franz-Josef Ulm,et al.  Hardness-packing density scaling relations for cohesive-frictional porous materials , 2008 .

[20]  G. Pharr,et al.  An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments , 1992 .

[21]  Franz-Josef Ulm,et al.  Nanochemomechanical assessment of shale: a coupled WDS-indentation analysis , 2012 .

[22]  Motofumi Ohki,et al.  Proposal for ISO 14577 : Metallic materials : Instrumented Indentation Test for Hardness and Materials Parameters (Part 1) Test Method (3rd. Influence on Computed Young's Modulus by Different Indenter's Tip Profile and Material Property (小特集 微小部および微小部材の評価技術) , 2012 .

[23]  C. W. Shih,et al.  Effect of tip radius on nanoindentation , 1991 .

[24]  Ruarri J. Day-Stirrat,et al.  Mechanical properties of organic matter in shales mapped at the nanometer scale , 2014 .

[25]  Dongxu Liu,et al.  An New Area Function for Sharp Indenter Tips in Nanoindentation , 2004 .

[26]  W. Nix,et al.  Instrumented nanoindentation and 3D mechanistic modeling of a shale at multiple scales , 2015 .

[27]  George M. Pharr,et al.  Instrumented Indentation Testing , 2000 .

[28]  Alexei Bolshakov,et al.  Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques , 1998 .

[29]  F. Ulm,et al.  The nano-mechanical morphology of shale , 2008 .

[30]  Cnpc Drilling.  Status quo and challenges of global shale gas drilling and completion , 2011 .