The maximum compression pressure position relative to top dead centre as an indication of engine cylinder condition and blowby

Abstract The compression curve of a DI (Direct Injection) diesel engine is affected by various parameters, such as heat loss, initial temperature and pressure, speed, compression ratio and blowby. Usually the engineer makes use of the measured motored pressure diagram and especially of the maximum compression pressure value to determine the engine condition (wear). However, in order to have an accurate indication of the engine condition, one must consider accurately all the previous mechanisms. This poses a very difficult task since, for example, not even the compression ratio is usually accurately known for an operating engine. Thus, a low maximum compression pressure value may not be caused by increased blowby rate, and so this may lead to a wrong indication of cylinder condition. The present work introduces a new method for determining cylinder condition (wear) and especially the blowby rate. The method is based on the determination of the position of the maximum compression pressure value relative to the TDC (Top Dead Centre) position. The maximum pressure position (before TDC) varies greatly with blowby rate, but is practically unaffected by heat losses, initial temperature and pressure and compression ratio. Experiments have been conducted on a Ricardo E-6, DI diesel engine for various compression ratios, engine speeds and operating temperatures (cold and warm operation) under motoring conditions. Pressure has been measured using a time step equivalent to 0.1°CA, while the TDC position has been determined using a magnetic pickup device. A mathematical simulation accounting for heat losses and blowby has been used to examine the effect of various parameters on maximum compression pressure and its position relative to TDC. The results from both experiments and simulation are found to be in good agreement concerning pressure curves, maximum pressure position and their variation with the parameters examined. The results are promising, showing a high potential for determining any cylinder condition by processing the corresponding measured pressure diagram.

[1]  Constantine D. Rakopoulos,et al.  Phasing cylinder pressure to crank angle in a direct injection diesel engine, by simulation of compression curve and elaboration of measured pressure data , 1991 .

[2]  Constantine D. Rakopoulos,et al.  Olive oil as a fuel supplement in DI and IDI diesel engines , 1992 .

[3]  James V. Beck,et al.  Parameter Estimation in Engineering and Science , 1977 .

[4]  B. Launder,et al.  Mathematical Models of turbulence , 1972 .

[5]  Dimitrios T. Hountalas,et al.  Prechamber and main chamber insulation effects on the performance of an IDI diesel engine coupled to power turbine , 1992 .

[6]  Constantine D. Rakopoulos,et al.  Availability accumulation and destruction in a DI diesel engine with special reference to the limited cooled case , 1993 .

[7]  Constantine D. Rakopoulos,et al.  Evaluation of a spark ignition engine cycle using first and second law analysis techniques , 1993 .

[8]  N. Watson,et al.  Thermodynamic Efficiency Evaluation of an Indirect Injection Diesel Engine , 1979 .

[9]  Constantine D. Rakopoulos,et al.  Ambient temperature and humidity effects on the performance and nitric oxide emission of spark ignition engined vehicles in Athens/Greece , 1988 .

[10]  Andrew P. Sage,et al.  System Identification , 1971 .

[11]  C. D. Rakopoulos,et al.  Influence of ambient temperature and humidity on the performance and emissions of nitric oxide and smoke of high speed diesel engines in the Athens/Greece region , 1991 .

[12]  Dimitrios T. Hountalas,et al.  Thermodynamic analysis of indirect injection diesel engines by two-zone modeling of combustion , 1990 .

[13]  N. Watson,et al.  HEAT TRANSFER IN THE INDIRECT INJECTION DIESEL ENGINE , 1979 .

[14]  C. D. Rakopoulos,et al.  Comparative performance and emission studies when using olive oil as a fuel supplement in DI and IDI diesel engines , 1992 .

[15]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[16]  E. Obert.  Internal combustion engines and air pollution , 1973 .

[17]  Dimitrios T. Hountalas,et al.  Thermodynamic analysis of a divided combustion chamber diesel engine , 1988 .