Heat generation and transfer in automotive dry clutch engagement

Dynamic behaviour of automotive dry clutches depends on the frictional characteristics of the contact between the friction lining material, the flywheel, and the pressure plate during the clutch engagement process. During engagement due to high interfacial slip and relatively high contact pressures, generated friction gives rise to contact heat, which affects the material behaviour and the associated frictional characteristics. In practice excess interfacial slipping and generated heat during torque transmission can result in wear of the lining, thermal distortion of the friction disc, and reduced useful life of the clutch. This paper provides measurement of friction lining characteristics for dry clutches for new and worn state under representative operating conditions pertaining to interfacial slipping during clutch engagement, applied contact pressures, and generated temperatures. An analytical thermal partitioning network model of the clutch assembly, incorporating the flywheel, friction lining, and the pressure plate is presented, based upon the principle of conservation of energy. The results of the analysis show a higher coefficient of friction for the new lining material which reduces the extent of interfacial slipping during clutch engagement, thus reducing the frictional power loss and generated interfacial heating. The generated heat is removed less efficiently from worn lining. This might be affected by different factors observed such as the reduced lining thickness and the reduction of density of the material but mainly because of poorer thermal conductivity due to the depletion of copper particles in its microstructure as the result of wear. The study integrates frictional characteristics, microstructural composition, mechanisms of heat generation, effect of lining wear, and heat transfer in a fundamental manner, an approach not hitherto reported in literature.

[1]  Homer Rahnejat,et al.  Effect of clutch lining frictional characteristics on take-up judder , 2017 .

[2]  Mehdi Ahmadian,et al.  Analysis of the influence of engine torque excitation on clutch judder , 2017 .

[3]  C. Chatwin,et al.  A thermal boundary control method for a flexible thin disk rotating over critical and supercritical speeds , 2017 .

[4]  Homer Rahnejat,et al.  An Analytical Approach for Prediction of Elastohydrodynamic Friction with Inlet Shear Heating and Starvation , 2016, Tribology Letters.

[5]  Mario Pisaturo,et al.  Simulation of engagement control in automotive dry-clutch and temperature field analysis through finite element model , 2016 .

[6]  F. Massi,et al.  Experimental and numerical analysis of frictional contact scenarios: from macro stick–slip to continuous sliding , 2015 .

[7]  David Crolla,et al.  Intelligent control of clutch judder and shunt phenomena in vehicle drivelines , 2014 .

[8]  P. Shahmohamadi,et al.  Convective Heat Transfer from a Heated Rotating Disk at Arbitrary Inclination Angle in Laminar Flow , 2013 .

[9]  Homer Rahnejat,et al.  Tribology of piston compression ring conjunction under transient thermal mixed regime of lubrication , 2013 .

[10]  Josef Schlattmann,et al.  Effect of Band Contact on the Temperature Distribution for Dry Friction Clutch , 2012 .

[11]  Y. Jang,et al.  Frictionally excited thermoelastic instability in a thin layer of functionally graded material sliding between two half-planes , 2009 .

[12]  Albert Albers,et al.  Fe thermal analysis of a ceramic clutch , 2009 .

[13]  Roland Larsson,et al.  Wet clutch friction characteristics obtained from simplified pin on disc test , 2008 .

[14]  Shuangmei Zhao,et al.  Behavior of a composite multidisk clutch subjected to mechanical and frictionally excited thermal load , 2008 .

[15]  Abdellatif Khamlichi,et al.  Optimizing the thermal properties of clutch facings , 2003 .

[16]  Alberto Bemporad,et al.  Hybrid control of dry clutch engagement , 2001, 2001 European Control Conference (ECC).

[17]  Luigi Glielmo,et al.  Optimal Control of Dry Clutch Engagement , 2000 .

[18]  A. F. Mills.  Basic Heat and Mass Transfer , 1999 .

[19]  Homer Rahnejat,et al.  The influence of the interface coefficient of friction upon the propensity to judder in automotive clutches , 1999 .

[20]  Andrew V. Olver,et al.  Testing Transmission Lubricants: The Importance of Thermal Response , 1991 .

[21]  T.F.J. Quinn,et al.  The role of wear in the failure of common tribosystems , 1984 .

[22]  T. P. Newcomb,et al.  TEMPERATURE DISTRIBUTIONS IN AUTOMOTIVE DRY CLUTCHES , 1976 .

[23]  Homer Rahnejat,et al.  Influence of clutch lining frictional characteristics upon cold and hot take-up judder , 2016 .

[24]  Homer Rahnejat,et al.  Clutch lining frictional characteristics under thermal tribodynamic conditions , 2016 .

[25]  Homer Rahnejat,et al.  Friction lining characteristics and the clutch take-up judder phenomenon with manual transmission , 2010 .

[26]  Abdellatif Khamlichi,et al.  Experimental characterization of frictional behaviour of clutch facings using Pin-on-disk machine , 2007 .

[27]  Homer Rahnejat,et al.  Non-linear multi-body dynamic analysis for the study of clutch torsional vibrations (judder) , 2001 .

[28]  R. Shah,et al.  Handbook of single-phase convective heat transfer , 1987 .

[29]  J. Lienhard.  A heat transfer textbook , 1981 .