Thermal Calibration Procedure and Thermal Characterisation of Low-cost Inertial Measurement Units

This paper investigates the thermal characteristics of typical Micro Electro-Mechanical System (MEMS) Inertial Measurement Units (IMUs) with a reliable thermal test procedure. Test results show that MEMS sensor errors, not only biases, but also scale factors and non-orthogonalities, may vary significantly with temperature. Also, MEMS sensor errors can have significant inconsistent curves under different temperature changing profiles. The existence of such inconsistencies posed a challenge to the following assumption of thermal calibration: the thermal drift of a sensor error is only related to the temperature of the sensor core. A robust way to mitigate this issue is given by using the sensor data during both heat-and-stay and cool-and-stay processes to establish the final thermal models. The performance of both IMUs and inertial navigation systems improved significantly after compensation with the established thermal models. Additionally, the variation of the IMU thermal parameters with time was observed, which suggests that periodical thermal calibration is necessary for MEMS IMUs.

[1]  John Weston,et al.  Strapdown Inertial Navigation Technology , 1997 .

[2]  Xiaoji Niu,et al.  An Accurate Land-Vehicle MEMS IMU/GPS Navigation System Using 3D Auxiliary Velocity Updates , 2007 .

[3]  Ahmed El-Rabbany,et al.  Temperature variation effects on stochastic characteristics for low-cost MEMS-based inertial sensor error , 2007 .

[4]  Quan Zhang,et al.  An in situ hand calibration method using a pseudo-observation scheme for low-end inertial measurement units , 2012 .

[5]  Sameh Nassar,et al.  Improving the Inertial Navigation System (INS) error model for INS and INS/DGPS applications , 2003 .

[6]  Andrew Y. C. Nee,et al.  Methods for in-field user calibration of an inertial measurement unit without external equipment , 2008 .

[7]  Naser El-Sheimy,et al.  A new multi-position calibration method for MEMS inertial navigation systems , 2007 .

[8]  Naser El-Sheimy,et al.  Thermal Calibration of Low Cost MEMS Sensors for Land Vehicle Navigation System , 2008, VTC Spring 2008 - IEEE Vehicular Technology Conference.

[9]  Xiaoji Niu,et al.  Fast Thermal Calibration of Low-Grade Inertial Sensors and Inertial Measurement Units , 2013, Sensors.

[10]  Jinling Wang,et al.  Land Vehicle Navigation with the Integration of GPS and Reduced INS: Performance Improvement with Velocity Aiding , 2010 .

[11]  Jari Kangas,et al.  An enhanced multi-position calibration method for consumer-grade inertial measurement units applied and tested , 2010 .

[12]  W. Abdel-Hamid.  AN ANFIS-Based Modeling of Thermal Drift of MEMS-Based Inertial Sensors , 2004 .

[13]  Yuanxin Wu,et al.  Improved multi-position calibration for inertial measurement units , 2009 .

[14]  Z. Berman.  Inertial Sensors-A New Approach for Low Cost Calibration and Testing , 2011 .

[15]  Eun-Hwan Shin,et al.  A New Calibration Method for Strapdown Inertial Navigation Systems , 2022 .

[16]  T.K. Tang,et al.  Temperature dependent characteristics of the JPL silicon MEMS gyroscope , 2000, 2000 IEEE Aerospace Conference. Proceedings (Cat. No.00TH8484).

[17]  Oliver J. Woodman,et al.  An introduction to inertial navigation , 2007 .

[18]  Z. Berman,et al.  Inertial sensors: Further developments in low-cost calibration and testing , 2012, Proceedings of the 2012 IEEE/ION Position, Location and Navigation Symposium.

[19]  Naser El-Sheimy,et al.  A Standard Testing and Calibration Procedure for Low Cost MEMS Inertial Sensors and Units , 2008, Journal of Navigation.