Numerical investigation of root canal irrigation adopting innovative needles with dimple and protrusion.

As important passive flow control methods, dimples and protrusions have been successfully implemented via geometric modifications to manipulate flow fields to get a desired flow parameters enhancement. In this research, two novel needles were proposed based on a prototype by means of the dimple and protrusion, and flow patterns within a root canal during final irrigation with these needles were numerically investigated. The calculation cases consistent with the clinically realistic irrigant flow rates, which are 0.02, 0.16 and 0.26 mL s(-1) are marked as case A, B and C, respectively. The characteristic parameters to estimate irrigation efficiency, such as shearing effect, mean apical pressure, irrigation replacement and fluid agitation, were compared and the optimal geometry in every calculation case was obtained. As shown from the results, flow rates and needle geometries were the causes of irrigation parameters variations. The sum of shear stress, irrigation replacement and fluid agitation were equal in the low flow rate case A, however, the needle with a protrusion on its tip had advantages in the three irrigation characteristic parameters above in calculation case B, and the needle with a dimple on its tip had advantages in calculation case C. Furthermore, the needles proposed did not give rise to the risk of irrigant extrusion. These needles can be better choices at larger flow rates. Therefore, needle geometry optimizations utilizing passive flow control methods are worthy to be investigated in the root canal irrigation enhancement.

[1]  Hongyu Yu,et al.  Optimization of intravascular shear stress assessment in vivo. , 2009, Journal of biomechanics.

[2]  Scott T. Lovald,et al.  The role of fluid dynamics in plaque excavation and rupture in the human carotid bifurcation: a computational study , 2009 .

[3]  Y. L. Moullec,et al.  CFD simulation of the hydrodynamics and reactions in an activated sludge channel reactor of wastewater treatment , 2010 .

[4]  Mohamed Gad-el-Hak,et al.  Modern developments in flow control , 1996 .

[5]  P. Bearman,et al.  Control of circular cylinder flow by the use of dimples , 1993 .

[6]  Nicholas Syred,et al.  Effect of Surface Curvature on Heat Transfer and Hydrodynamics Within a Single Hemispherical Dimple , 2000 .

[7]  David A. Vorp,et al.  Computational modeling of arterial biomechanics: insights into pathogenesis and treatment of vascular disease. , 2003, Journal of vascular surgery.

[8]  L W M van der Sluis,et al.  Irrigant flow in the root canal: experimental validation of an unsteady Computational Fluid Dynamics model using high-speed imaging. , 2010, International endodontic journal.

[9]  K. Gulabivala,et al.  Effects of mechanical and chemical procedures on root canal surfaces , 2005 .

[10]  Jongmyung Park,et al.  NUMERICAL PREDICTIONS OF HEAT TRANSFER AND FLUID FLOW CHARACTERISTICS FOR SEVEN DIFFERENT DIMPLED SURFACES IN A CHANNEL , 2005 .

[11]  Werayut Srituravanich,et al.  Review on Micro- and Nanolithography Techniques and Their Applications , 2012 .

[12]  I. Eames,et al.  The fluid mechanics of root canal irrigation , 2010, Physiological measurement.

[13]  Yuan Gao,et al.  Development and validation of a three-dimensional computational fluid dynamics model of root canal irrigation. , 2009, Journal of endodontics.

[14]  Michel Versluis,et al.  Evaluation of irrigant flow in the root canal using different needle types by an unsteady computational fluid dynamics model. , 2010, Journal of endodontics.

[15]  Minrui Fei,et al.  Modeling of the Human Bronchial Tree and Simulation of Internal Airflow: A Review , 2010, LSMS/ICSEE.

[16]  H. Y. Luo,et al.  Modeling the bifurcating flow in a CT-scanned human lung airway. , 2008, Journal of biomechanics.

[17]  Di Zhang,et al.  Effect of leading edge boundary layer thickness on dimple flow structure and separation control , 2011 .

[18]  Ihtesham H. Chowdhury,et al.  Numerical Heat Transfer, Part A: Applications , 2007 .

[19]  O A Peters,et al.  Effects of four Ni-Ti preparation techniques on root canal geometry assessed by micro computed tomography. , 2001, International endodontic journal.

[20]  M-K Wu,et al.  The effectiveness of syringe irrigation and ultrasonics to remove debris from simulated irregularities within prepared root canal walls. , 2004, International endodontic journal.

[21]  Leandro R Britto,et al.  The effect of exposure to irrigant solutions on apical dentin biofilms in vitro. , 2006, Journal of endodontics.

[22]  E. Kastrinakis,et al.  Measurement of pressure and flow rates during irrigation of a root canal ex vivo with three endodontic needles. , 2007, International endodontic journal.

[23]  Joaquín Izquierdo,et al.  Computational fluid dynamics (CFD) models in the learning process of Hydraulic Engineering , 2010, Comput. Appl. Eng. Educ..

[24]  Yuan Gao,et al.  Three-dimensional numeric simulation of root canal irrigant flow with different irrigation needles. , 2010, Journal of Endodontics.

[25]  Di Zhang,et al.  Flow and Heat Transfer in Microchannels With Dimples and Protrusions , 2012 .

[26]  C Boutsioukis,et al.  Irrigant flow within a prepared root canal using various flow rates: a Computational Fluid Dynamics study. , 2009, International endodontic journal.

[27]  Paul G. Tucker,et al.  Level sets for CFD in aerospace engineering , 2010 .

[28]  M. L. Hill,et al.  Flow structure due to dimple depressions on a channel surface , 2001 .