Numerical study of the effects of injection-port design on the heating performance of an R134a heat pump with vapor injection used in electric vehicles

Abstract Heat pumps, which enable the cooling and heating of vehicular cabins, consume a significant portion of the total energy consumption in electric vehicles (EVs). The efficiency of the heat pump is typically degraded owing to cold-weather conditions, so the refrigerant-injection technique has been proposed for improving the system performance and compressor reliability. In this study, a simulation model for an R134a heat pump with vapor injection is developed and validated by performing thermodynamic analyses with geometrical information. The effects of the injection-port design are investigated using the developed numerical model. Single-injection and dual-injection ports are considered to optimize the coefficient of performance (COP) and isentropic efficiency by controlling the injection mass flow rate. The optimal angles of the single- and dual-injection ports are determined to be 440° and 535°/355° (for pocket A/B), respectively, while the corresponding COPs are improved by 7.5% and 9.8%, respectively, compared to the non-injection heat pump at an outdoor temperature of −10 °C.

[1]  René Rieberer,et al.  Simulation based identification of the ideal defrost start time for a heat pump system for electric vehicles , 2015 .

[2]  Huiming Zou,et al.  Experimental investigation on heating performance of heat pump for electric vehicles at −20 °C ambient temperature , 2015 .

[3]  Chul Woo Roh,et al.  VAPOR REFRIGERANT INJECTION TECHNIQUES FOR HEAT PUMP SYSTEMS: THE LATEST LITERATURE REVIEW AND DISCUSSION , 2014 .

[4]  Yongchan Kim,et al.  Performance of a Two-Phase Injection Heat Pump with the Variation of Injection Quality and Pressure , 2017 .

[5]  S. Churchill,et al.  Correlating equations for laminar and turbulent free convection from a vertical plate , 1975 .

[6]  Reinhard Radermacher,et al.  Refrigerant injection for heat pumping/air conditioning systems: Literature review and challenges discussions , 2011 .

[7]  Chi-Chuan Wang,et al.  A generalized heat transfer correlation for Iouver fin geometry , 1997 .

[8]  Min-Soo Kim,et al.  Heating performance enhancement of a CO2 heat pump system recovering stack exhaust thermal energy in fuel cell vehicles , 2007 .

[9]  Shigeru Koyama,et al.  An experimental study on condensation of refrigerant R134a in a multi-port extruded tube , 2003 .

[10]  Mo Se Kim,et al.  Performance evaluation of a vapor injection heat pump system for electric vehicles , 2017 .

[11]  Mustafa Canakci,et al.  Performance evaluation of an R134a automotive heat pump system for various heat sources in comparison with baseline heating system , 2015 .

[12]  Xianting Li,et al.  Numerical analysis on the effects of refrigerant injection on the scroll compressor , 2006 .

[13]  Yong Chan Kim,et al.  Optimization of injection holes in symmetric and asymmetric scroll compressors with vapor injection , 2012 .

[14]  R. Webb,et al.  Correlation of two-phase friction for refrigerants in small-diameter tubes , 2001 .

[15]  Jong-Phil Won,et al.  Performance characteristics of mobile heat pump for a large passenger electric vehicle , 2013 .

[16]  Yangguang Liu,et al.  Mathematical model of bypass behaviors used in scroll compressor , 2009 .

[17]  K. Y. Kim,et al.  Experimental studies on the heating performance of the PTC heater and heat pump combined system in fuel cells and electric vehicles , 2012 .

[18]  Xiande Fang.  A new correlation of flow boiling heat transfer coefficients based on R134a data , 2013 .

[19]  Sangkwon Jeong,et al.  Experimental investigation on convective heat transfer mechanism in a scroll compressor , 2006 .

[20]  Xinyu Zhang,et al.  Study on Economized Vapor Injection Heat Pump System Using Refrigerant R32 , 2016 .

[21]  Hae Won Jung,et al.  Heating performance characteristics of a dual source heat pump using air and waste heat in electric vehicles , 2014 .