Ultrasound assisted continuous‐mixing for the preparation of PP/SEBS/OMMT ternary nanocomposites

Polypropylene (PP)/polystyrene-block-poly(ethylene-co-butylenes)-block-polystyrene (SEBS)/organo-montmorillonite (OMMT) nanocomposites of varying concentrations of maleic anhydride-grafted polypropylene (PP-g-MA) were prepared by continuous mixing assisted by ultrasonic oscillation. The structure and morphology of nanocomposites were investigated by X-ray diffraction (XRD), transmission electron microscopy, and scanning electron microscopy. It was found that both PP-g-MA and ultrasonic oscillation could enhance the intercalation and exfoliation of OMMT in PP matrix. Meanwhile, the formation of PP could be induced by ultrasonic irradiation at a power of more than 540 W. Rheological properties including complex viscosity, storage, and loss modulus of nanocomposites were increased after adding PP-g-MA or ultrasonic treatment. The results of mechanical properties showed that PP-g-MA could improve the tensile strength and tensile modulus of nanocomposites, but with the sacrifice of impact strength. This problem could be improved by ultrasound due to the reduced particle size of SEBS. However, the mechanical properties would be reduced by ultrasonic treatment with higher intensity due to the polymer degradation. Therefore, the synergistic effect of both compatibilizer and ultrasound should account for the balance between toughness and stiffness of PP/SEBS/OMMT ternary nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 41202.

[1]  S. Bensaad,et al.  The Effects of Organoclay on the Morphology and Balance Properties of an Immiscible Polypropylene/Natural Rubber Blend , 2013 .

[2]  R. Hadimani,et al.  The potential for ultrasound to improve nanoparticle dispersion and increase flame resistance in fibre-forming polymers , 2012 .

[3]  C. Nicolae,et al.  Effect of SEBS on morphology, thermal, and mechanical properties of PP/organoclay nanocomposites , 2012, Polymer Bulletin.

[4]  F. Sharif,et al.  Effect of material and processing parameters on mechanical properties of Polypropylene/Ethylene–Propylene–Diene–Monomer/clay nanocomposites , 2011 .

[5]  Hanxiong Huang,et al.  Microstructure and mechanical properties of polypropylene/poly (ethylene-co-octene copolymer)/clay ternary nanocomposites prepared by melt blending using supercritical carbon dioxide as a processing aid , 2011 .

[6]  Sung-Po Liu,et al.  Preparation and mechanical properties of polypropylene / montmorillonite nanocomposites - After grafted with hard/soft grafting agent , 2011 .

[7]  K. Nagata,et al.  Influence of Filler Size on Impact Properties of PP/Elastomer/Filler Ternary Composites , 2011 .

[8]  H. Ade,et al.  Interfacial Interactions in PP/MMT/SEBS Nanocomposites , 2010 .

[9]  Hanxiong Huang,et al.  Mechanical and rheological properties of PP/SEBS/OMMT ternary composites , 2009 .

[10]  N. Cai,et al.  Polypropylene/silica nanocomposites prepared by in-situ melt ultrasonication , 2009 .

[11]  D. R. Paul,et al.  Nanocomposites formed from polypropylene/EVA blends , 2009 .

[12]  Todd M. Lewis,et al.  Ultrasound assisted twin screw extrusion of polymer–nanocomposites containing carbon nanotubes , 2009 .

[13]  M. Rong,et al.  Phase structure and mechanical properties of ternary polypropylene/elastomer/nano-CaCO3 composites , 2007 .

[14]  S. Tjong,et al.  Impact essential work of fracture of polypropylene/montmorillonite nanocomposites toughened with SEBS-g-MA elastomer , 2007 .

[15]  Avraam Isayev,et al.  Effect of ultrasound on HDPE/clay nanocomposites: Rheology, structure and properties , 2007 .

[16]  Jae Wook Lee,et al.  Continuous extrusion of long-chain-branched polypropylene/clay nanocomposites with high-intensity ultrasonic waves , 2007 .

[17]  Yiqun Liu,et al.  The structure and physical properties of polypropylene and thermoplastic olefin nanocomposites containing nanosilica , 2006 .

[18]  Fan Yang,et al.  Structure and properties of SEBS/PP/OMMT nanocomposites , 2006 .

[19]  A. Isayev,et al.  Continuous process for melt intercalation of PP–clay nanocomposites with aid of power ultrasound , 2006 .

[20]  Donald R Paul,et al.  TPO based nanocomposites. Part 1. Morphology and mechanical properties , 2005 .

[21]  S. Tjong,et al.  Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship , 2005 .

[22]  I. Šmit,et al.  Polypropylene/talc/SEBS (SEBS-g-MA) composites. Part 2. Mechanical properties , 2005 .

[23]  Shaoyun Guo,et al.  Mechanochemical degradation kinetics of high-density polyethylene melt and its mechanism in the presence of ultrasonic irradiation. , 2005, Ultrasonics sonochemistry.

[24]  D. Mielewski,et al.  Exfoliation and dispersion enhancement in polypropylene nanocomposites by in‐situ melt phase ultrasonication , 2004 .

[25]  Hyungsun Kim,et al.  Characteristics of polystyrene/polyethylene/clay nanocomposites prepared by ultrasound-assisted mixing process , 2004 .

[26]  J. Oh,et al.  Continuous ultrasonic process for in situ compatibilization of polypropylene/natural rubber blends , 2003 .

[27]  Huilin Li,et al.  Influence of ultrasound on the processing and structure of polypropylene during extrusion , 2002 .

[28]  Huilin Li,et al.  The effects of ultrasonic irradiation on the crystalline structures of nucleated polypropylene , 2002 .

[29]  Shiai Xu,et al.  Mechanical behavior and fracture toughness evaluation of maleic anhydride compatibilized short glass fiber/SEBS/polypropylene hybrid composites , 2002 .

[30]  K. Premphet,et al.  Quantitative characterization of dispersed particle size, size distribution, and matrix ligament thickness in polypropylene blended with metallocene ethylene–octene copolymers , 2001 .