Adhesion tilt-tolerance in bio-inspired mushroom-shaped adhesive microstructure

We studied experimentally and theoretically the effect of different tilt angles on the adhesion of mushroom-shaped adhesive microstructures. The marginal measured influence of tilting on pull-off forces is quantitatively well confirmed by numerical and theoretical calculations and was shown to be a direct consequence of an optimized stress distribution. In addition, the presence of a joint-like narrowing under the contact elements, as found in some biological attachment systems, was shown to further contribute to the tilt-tolerance. The results obtained allow us to explain the advantage of the widely observed mushroom-shaped contact geometry in nature for long-term and permanent adhesion.

[1]  I. N. Sneddon.  The distribution of stress in the neighbourhood of a crack in an elastic solid , 1946, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[2]  P. C. Paris,et al.  The Stress Analysis of Cracks Handbook, Third Edition , 2000 .

[3]  Hiroshi Tada,et al.  The stress analysis of cracks handbook , 2000 .

[4]  R. Full,et al.  Adhesive force of a single gecko foot-hair , 2000, Nature.

[5]  S. Gorb.  Attachment Devices of Insect Cuticle , 2001, Springer Netherlands.

[6]  S. Gorb,et al.  Evolution of locomotory attachment pads in the Dermaptera (Insecta). , 2004, Arthropod structure & development.

[7]  S. Gorb,et al.  Biomimetic mushroom-shaped fibrillar adhesive microstructure , 2007, Journal of The Royal Society Interface.

[8]  Metin Sitti,et al.  Biologically inspired polymer microfibers with spatulate tips as repeatable fibrillar adhesives , 2006 .

[9]  Stanislav N. Gorb,et al.  Mushroom-shaped geometry of contact elements in biological adhesive systems , 2007 .

[10]  S. Gorb,et al.  Close-up of mushroom-shaped fibrillar adhesive microstructure: contact element behaviour , 2007, Journal of The Royal Society Interface.

[11]  Metin Sitti,et al.  Enhanced friction of elastomer microfiber adhesives with spatulate tips , 2007 .

[12]  Eduard Arzt,et al.  Contact shape controls adhesion of bioinspired fibrillar surfaces. , 2007, Langmuir : the ACS journal of surfaces and colloids.

[13]  M. Sitti,et al.  Gecko-inspired directional and controllable adhesion. , 2008, Small.

[14]  Carlo Menon,et al.  A low-cost, high-yield fabrication method for producing optimized biomimetic dry adhesives , 2009 .

[15]  J. P. Sargent,et al.  A practical approach to the development of a synthetic Gecko tape , 2009 .

[16]  Nicola Pugno,et al.  Spatulate structures in biological fibrillar adhesion , 2010 .

[17]  Giuseppe Carbone,et al.  Origin of the superior adhesive performance of mushroom-shaped microstructured surfaces , 2011 .

[18]  Alexander Filippov,et al.  Shear induced adhesion: contact mechanics of biological spatula-like attachment devices. , 2011, Journal of theoretical biology.

[19]  E. Arzt,et al.  Bioinspired pressure actuated adhesive system , 2011 .

[20]  G. Carbone,et al.  Sticky bio-inspired micropillars: finding the best shape. , 2012, Small.

[21]  Stanislav N. Gorb,et al.  First mushroom-shaped adhesive microstructure: A review , 2012 .

[22]  Lars Heepe,et al.  Adhesion failure at 180,000 frames per second: direct observation of the detachment process of a mushroom-shaped adhesive. , 2013, Physical review letters.

[23]  G. Carbone,et al.  The Mechanisms of Detachment of Mushroom-Shaped Micro-Pillars: From Defect Propagation to Membrane Peeling , 2013 .

[24]  S. Gorb,et al.  Male clasping ability, female polymorphism and sexual conflict: fine-scale elytral morphology as a sexually antagonistic adaptation in female diving beetles , 2013, Journal of The Royal Society Interface.