Biomechanical Evaluation of Relationship of Screw Pullout Strength, Insertional Torque, and Bone Mineral Density in the Cervical Spine

Background: Understanding of implant failure mechanisms is important in the successful utilization of anterior cervical plates. Many variables influence screw purchase, including the quality of the bone. The purpose of this study was to assess the relationship of screw pullout and screw insertional torque across a wide range of bone mineral densities (BMDs). Methods: A total of 54 cervical vertebrae in 12 cervical spines were evaluated for BMD using dual-energy x-ray absorptiometry scanning. Actual and perceived peak torques of 3.5-mm anterior cervical screws were determined at each level followed by screw pullout strength testing. Results: A high correlation was observed between screw pullout strength and BMD. However, there was a low correlation of peak insertional torque to pullout strength. Conclusion: These findings suggest the quality of the bone is more instrumental in the success or failure of anterior cervical screws than is the insertional torque with which the screws are placed.

[1]  奥山 幸一郎,et al.  Stability of transpedicle screwing for the osteoporotic spine , 1994 .

[2]  D N Kunz,et al.  Pedicle Screw Pullout Strength: Correlation with Insertional Torque , 1993, Spine.

[3]  Jeffrey C. Wang,et al.  Increased Fusion Rates With Cervical Plating for Three-Level Anterior Cervical Discectomy and Fusion , 2001, Spine.

[4]  A. Minami,et al.  Biomechanical Evaluation of Anterior Spinal Instrumentation Systems for Scoliosis: In Vitro Fatigue Simulation , 2001, Spine.

[5]  Timothy C Ryken,et al.  Biomechanical analysis of bone mineral density, insertion technique, screw torque, and holding strength of anterior cervical plate screws. , 1995, Journal of neurosurgery.

[6]  Jeffrey C. Wang,et al.  Increased Fusion Rates With Cervical Plating for Two-Level Anterior Cervical Discectomy and Fusion , 2000, Spine.

[7]  J. Torner,et al.  Factors Affecting the Pullout Strength of Self-Drilling and Self-Tapping Anterior Cervical Screws , 2003, Spine.

[8]  D. E. Swartz,et al.  Importance of bone mineral density in instrumented spine fusions. , 1991, Spine.

[9]  T. Ryken,et al.  Assessment of primary and salvage lateral mass screw insertion torque in a cadaveric model. , 1997, Journal of spinal disorders.

[10]  Peter‐Michael Zink,et al.  Performance of Ventral Spondylodesis Screws in Cervical Vertebrae of Varying Bone Mineral Density , 1996, Spine.

[11]  B. Snyder,et al.  Predicting the Integrity of Vertebral Bone Screw Fixation in Anterior Spinal Instrumentation , 1995, Spine.

[12]  R M Harrington,et al.  Factors affecting the pullout strength of cancellous bone screws. , 1996, Journal of biomechanical engineering.

[13]  島本 則道.  Biomechanical evaluation of anterior spinal instrumentation systems for scoliosis : In vitro fatigue simulation , 2002 .

[14]  M. Pope,et al.  Correlation of bone equivalent mineral density to pull-out resistance of triangulated pedicle screw construct. , 1997, Journal of spinal disorders.

[15]  P. McAfee,et al.  Influence of Bone Mineral Density on the Fixation of Thoracolumbar Implants A Comparative Study of Transpedicular Screws, Laminar Hooks, and Spinous Process Wires , 1990, Spine.

[16]  C. Reitman,et al.  Cervical plates: comparison of physical characteristics and in vitro pushout strength. , 2003, The spine journal : official journal of the North American Spine Society.

[17]  K Okuyama,et al.  Stability of transpedicle screwing for the osteoporotic spine. An in vitro study of the mechanical stability. , 1993, Spine.

[18]  H. An,et al.  Strength of anterior vertebral screw fixation in relationship to bone mineral density. , 1995, Journal of spinal disorders.