Additive manufacturing with polypropylene microfibers.

The additive manufacturing of small diameter polypropylene microfibers is described, achieved using a technique termed melt electrospinning writing. Sequential fiber layering, which is important for accurate three-dimensional fabrication, was achieved with the smallest fiber diameter of 16.4±0.2μm obtained. The collector speed, temperature and melt flow rate to the nozzle were optimized for quality and minimal fiber pulsing. Of particular importance to the success of this method is appropriate heating of the collector plate, so that the electrostatically drawn filament adheres during the direct-writing process. By demonstrating the direct-writing of polypropylene, new applications exploiting the favorable mechanical, stability and biocompatible properties of this polymer are envisaged.

[1]  Tong Lin,et al.  Needleless melt-electrospinning of polypropylene nanofibres , 2012 .

[2]  Shanhui Fan,et al.  Direct‐Write Assembly of Three‐Dimensional Photonic Crystals: Conversion of Polymer Scaffolds to Silicon Hollow‐Woodpile Structures , 2006 .

[3]  J. Ochsner,et al.  Hernia repair with Marlex mesh. A comparison of techniques. , 1959, Surgery.

[4]  P. Dalton,et al.  Fibre pulsing during melt electrospinning writing , 2016 .

[5]  Dietmar W Hutmacher,et al.  Direct Writing By Way of Melt Electrospinning , 2011, Advanced materials.

[6]  Michael Wehmann,et al.  Melt blowing technology , 1999 .

[7]  Frank Ko,et al.  Melt-electrospinning. part I: processing parameters and geometric properties , 2004 .

[8]  J. Spruiell,et al.  Melt spinning of polypropylene , 1999 .

[9]  F. C. Usher.  Braided Marlex suture. A new general purpose suture. , 1961, Archives of surgery.

[10]  Kiyohito Koyama,et al.  Relation between tacticity and fiber diameter in melt-electrospinning of polypropylene , 2009 .

[11]  J. Hubbell,et al.  Chapter 6 Materials selection , 1993 .

[12]  Dietmar W Hutmacher,et al.  Melt electrospinning and its technologization in tissue engineering. , 2015, Tissue engineering. Part B, Reviews.

[13]  I Zein,et al.  Mechanical properties and cell cultural response of polycaprolactone scaffolds designed and fabricated via fused deposition modeling. , 2001, Journal of biomedical materials research.

[14]  Dietmar W Hutmacher,et al.  Melt electrospinning of poly(ε-caprolactone) scaffolds: phenomenological observations associated with collection and direct writing. , 2014, Materials science & engineering. C, Materials for biological applications.

[15]  Jiankang He,et al.  Development of melt electrohydrodynamic 3D printing for complex microscale poly (ε-caprolactone) scaffolds , 2016, Biofabrication.

[16]  D. Hutmacher,et al.  Chapter 6:Design and Fabrication of Scaffolds via Melt Electrospinning for Applications in Tissue Engineering , 2015 .

[17]  Adrian J. T. Teo,et al.  Polymeric Biomaterials for Medical Implants and Devices. , 2016, ACS biomaterials science & engineering.

[18]  Dong-Woo Cho,et al.  Biofabrication: reappraising the definition of an evolving field , 2016, Biofabrication.

[19]  Y. Liu,et al.  Morphologies and crystal structures of styrene–acrylonitrile/isotactic polypropylene ultrafine fibers fabricated by melt electrospinning , 2013 .

[20]  John F. Rabolt,et al.  Micro- and Nanostructured Surface Morphology on Electrospun Polymer Fibers , 2002 .

[21]  Fei Chen,et al.  Additive Manufacturing of a Photo-Cross-Linkable Polymer via Direct Melt Electrospinning Writing for Producing High Strength Structures. , 2016, Biomacromolecules.

[22]  Seungsin Lee,et al.  Developing protective textile materials as barriers to liquid penetration using melt-electrospinning , 2006 .

[23]  Y. Bilsel,et al.  The search for ideal hernia repair; mesh materials and types. , 2012, International journal of surgery.

[24]  Jos Malda,et al.  Reinforcement of hydrogels using three-dimensionally printed microfibres , 2015, Nature Communications.

[25]  Y. Truong,et al.  Melt-electrospinning of polypropylene with conductive additives , 2012, Journal of Materials Science.

[26]  Tim R. Dargaville,et al.  Dermal fibroblast infiltration of poly(ε-caprolactone) scaffolds fabricated by melt electrospinning in a direct writing mode , 2013, Biofabrication.

[27]  H. Schmidt,et al.  Shaping self-assembling small molecules into fibres by melt electrospinning , 2012 .

[28]  M. Kotaki,et al.  A review on polymer nanofibers by electrospinning and their applications in nanocomposites , 2003 .

[29]  J. Groll,et al.  High definition fibrous poly(2-ethyl-2-oxazoline) scaffolds through melt electrospinning writing , 2014 .

[30]  Debra J. Audus,et al.  Structural properties and superhydrophobicity of electrospun polypropylene fibers from solution and melt , 2010 .

[31]  Martin Möller,et al.  Electrospinning of polymer melts: Phenomenological observations , 2007 .

[32]  Scott J Hollister,et al.  Additive manufacturing of polymer melts for implantable medical devices and scaffolds , 2017, Biofabrication.

[33]  P. Dalton,et al.  Additive manufacturing of scaffolds with sub-micron filaments via melt electrospinning writing , 2015, Biofabrication.

[34]  Dietmar W. Hutmacher,et al.  Melt electrospinning today: An opportune time for an emerging polymer process , 2016 .

[35]  P. Dobrin.  Suture Selection for Hernia Repair , 2001 .

[36]  M. M. Bubakir,et al.  Polypropylene fibers fabricated via a needleless melt-electrospinning device for marine oil-spill cleanup , 2014 .

[37]  Tim R. Dargaville,et al.  Hierarchically Structured Porous Poly(2-oxazoline) Hydrogels. , 2016, Macromolecular rapid communications.

[38]  Dietmar W. Hutmacher,et al.  Design and Fabrication of Tubular Scaffolds via Direct Writing in a Melt Electrospinning Mode , 2012, Biointerphases.

[39]  Jon Baskin.  Chapter 6 , 2003, Tom Sawyer Abroad / Tom Sawyer, Detective.

[40]  Dietmar W Hutmacher,et al.  Electrospinning and additive manufacturing: converging technologies. , 2013, Biomaterials science.

[41]  B. Heniford,et al.  The Argument for Lightweight Polypropylene Mesh in Hernia Repair , 2005, Surgical innovation.