Reliability Enhancement of MEMS Lateral Comb Resonators Under Fault Conditions

The delicate structure of microelectromechanical systems (MEMS) limits their reliability in cases of fault occurrence. Control systems can enhance their reliability of operation by providing fault robust systems. This paper illustrates a method for the safe operation of lateral comb resonators (LCR) under faulty conditions. Different types of fault are fabricated at chip level and experimentally tested in order to demonstrate the effectiveness of the reliability enhancement of operation in LCRs. Mass change and folded spring structural defects influence the device's behavior and reduce its reliability of operation. Here, model reference adaptive controllers (MRACs) are effectively used to enhance the reliability of faulty devices. Reliable operation of a +5% additional mass considering environmental conditions and asymmetries on the device, demand almost 80% higher control effort whereas +20% in case of broken trusses or +46% in case of adhesion point fault on a beam of folded springs. The simulation and experiment results demonstrate successful application of MRAC for reliable operation of LCRs by providing a fault-robust system.

[1]  T. Tsuchiya,et al.  Specimen size effect on tensile strength of surface micromachined polycrystalline silicon thin films , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[2]  J. Bryzek,et al.  Control issues for MEMS , 2003, 42nd IEEE International Conference on Decision and Control (IEEE Cat. No.03CH37475).

[3]  Jian-Ping Li,et al.  A method to take account of inhomogeneity in mechanical component reliability calculations , 2005, IEEE Transactions on Reliability.

[4]  Roberto Horowitz,et al.  Dynamics and control of micromachined gyroscopes , 1999, Proceedings of the 1999 American Control Conference (Cat. No. 99CH36251).

[5]  Limin Wang,et al.  MEMS feedback control using through-wafer optical device monitoring , 2000, SPIE MOEMS-MEMS.

[6]  Robert Patton Leland,et al.  Adaptive control of a MEMS gyroscope using Lyapunov methods , 2006, IEEE Transactions on Control Systems Technology.

[7]  M. Gad-el-Hak.  The MEMS Handbook , 2001 .

[8]  A. P. Dorey,et al.  Fault simulation for MEMS , 1999 .

[9]  D. S. Walsh,et al.  Radiation effects on surface micromachined comb drives and microengines , 1998 .

[10]  Parviz Famouri,et al.  Through-wafer optical probe characterization for microelectromechanical systems positional state monitoring and feedback control , 2000 .

[11]  R. Monopoli.  Model reference adaptive control with an augmented error signal , 1974 .

[12]  E. Jansen,et al.  Reliability and long term stability of MEMS , 1996, Digest IEEE/Leos 1996 Summer Topical Meeting. Advanced Applications of Lasers in Materials and Processing.

[13]  Jack W. Judy,et al.  Microelectromechanical systems (MEMS): fabrication, design and applications , 2001 .

[14]  R. D. Blanton,et al.  Development of a MEMS testing methodology , 1997, Proceedings International Test Conference 1997.

[15]  V. T. Srikar,et al.  The reliability of microelectromechanical systems (MEMS) in shock environments , 2002 .

[16]  P.S. Reddy,et al.  Pattern alignment effects in through-wafer bulk micromachining of (100) silicon , 2004, 2004 IEEE Workshop on Microelectronics and Electron Devices.

[17]  Ernest J. Garcia,et al.  Microfabricated actuators and their application to optics , 1995, Photonics West.

[18]  Roberto Horowitz,et al.  Adaptive controller design of MEMS gyroscopes , 2001, ITSC 2001. 2001 IEEE Intelligent Transportation Systems. Proceedings (Cat. No.01TH8585).

[19]  R. D. Blanton,et al.  MEMS fault model generation using CARAMEL , 1998, Proceedings International Test Conference 1998 (IEEE Cat. No.98CH36270).

[20]  Weiping Li,et al.  Applied Nonlinear Control , 1991 .

[21]  P. Famouri,et al.  Real-time translational control of a MEMS comb resonator , 2004, IEEE Transactions on Aerospace and Electronic Systems.

[22]  Norihiko Kato,et al.  Performance improvement of a magnetically levitated microrobot using an adaptive control , 2003, Proceedings International Conference on MEMS, NANO and Smart Systems.

[23]  Ernest J. Garcia,et al.  Surface micromachined microengine , 1995 .

[24]  A. Izadian,et al.  Trajectory Control of MEMS Lateral Comb Resonators Under Faulty Conditions , 2007, 2007 American Control Conference.

[25]  Roberto Horowitz,et al.  Identification, position sensing, and control of an electrostatically-driven polysilicon microactuator , 1995, Proceedings of 1995 34th IEEE Conference on Decision and Control.

[26]  Roberto Horowitz,et al.  Adaptive control for the conventional mode of operation of MEMS gyroscopes , 2002 .

[27]  Leslie M. Phinney,et al.  Process yields for laser repair of aged, stiction-failed, MEMS devices , 2001 .

[28]  L. Hornak,et al.  ADAPTIVE CONTROL OF MEMS DEVICES , 2022 .

[29]  Petros A. Ioannou,et al.  Adaptive control tutorial , 2006, Advances in design and control.

[30]  Limin Wang,et al.  Stroke-length control of a MEMS device , 2000, ISIE'2000. Proceedings of the 2000 IEEE International Symposium on Industrial Electronics (Cat. No.00TH8543).

[31]  William C. Tang,et al.  Viscous air damping in laterally driven microresonators , 1994, Proceedings IEEE Micro Electro Mechanical Systems An Investigation of Micro Structures, Sensors, Actuators, Machines and Robotic Systems.

[32]  V. Samper,et al.  MEMS failure analysis and reliability , 2003, Proceedings of the 10th International Symposium on the Physical and Failure Analysis of Integrated Circuits. IPFA 2003.