Experimental investigation of local-overall interaction buckling of stainless steel lipped channel columns

Abstract A detailed finite element (FE) model is presented, which was developed with the aim of studying the interaction of local and overall buckling in stainless steel columns. The model incorporates non-linear stress–strain behaviour, anisotropy, enhanced corner properties and initial imperfections. The model was verified against a program of 29 laboratory tests on stainless steel lipped channels, described in a companion paper [Becque J, Rasmussen KJR. Experimental investigation of the interaction of local and overall buckling of stainless steel lipped channel columns. Journal of Constructional Steel Research 2009; 65(8–9): 1677–84] and yielded excellent predictions of ultimate strength and specimen behaviour. The FE model was further used in parametric studies, varying both the cross-sectional slenderness and the overall slenderness. Three stainless steel alloys were considered: AISI304, AISI430 and 3Cr12. The results are compared with the governing design rules of the Australian, North American and European standards for stainless steel structures.

[1]  A. C. Walker.  Design and analysis of cold-formed sections , 1975 .

[2]  Ehab Ellobody.  Buckling analysis of high strength stainless steel stiffened and unstiffened slender hollow section columns , 2007 .

[3]  Ben Young,et al.  Buckling of stainless steel square hollow section compression members , 2003 .

[4]  R. Hill.  The mathematical theory of plasticity , 1950 .

[5]  Kim J.R. Rasmussen,et al.  Design of Cold-Formed Stainless Steel Tubular Members. II: Beams , 1993 .

[6]  Ben Young,et al.  Tests of cold-formed high strength stainless steel compression members , 2006 .

[7]  Leroy Gardner,et al.  Structural design of high-strength austenitic stainless steel , 2006 .

[8]  Kim J.R. Rasmussen,et al.  Experimental Investigation of the Interaction of Local and Overall Buckling of Stainless Steel I-Columns , 2009 .

[9]  Ben Young,et al.  Column design of cold-formed stainless steel slender circular hollow sections , 2006 .

[10]  A. van der Neut,et al.  The interaction of local buckling and column failure of thin-walled compression members , 1969 .

[11]  null null,et al.  Specification for the Design of Cold-Formed Stainless Steel Structural Members , 2002 .

[12]  David A. Nethercot,et al.  Numerical Modeling of Stainless Steel Structural Components—A Consistent Approach , 2004 .

[13]  George Winter.  Stress Distribution in and Equivalent Width of Flanges of Wide, Thin-Wall Steel Beams , 1940 .

[14]  Theodore V. Galambos,et al.  Guide to stability design criteria for metal structures , 1998 .

[15]  Kim J.R. Rasmussen,et al.  Strength Curves for Metal Columns , 1997 .

[16]  Hans H. Bleich,et al.  Buckling strength of metal structures , 1952 .

[17]  Ben Young,et al.  Experimental investigation of cold-formed stainless steel columns , 2002 .

[18]  David A. Nethercot,et al.  Experiments on stainless steel hollow sections—Part 2: Member behaviour of columns and beams , 2004 .

[19]  Gregory J. Hancock,et al.  Computer analysis of thin-walled structural members , 1995 .

[20]  Ehab Ellobody,et al.  Structural performance of cold-formed high strength stainless steel columns , 2005 .

[21]  G. J. van den Berg,et al.  The effect of the non-linear stress–strain behaviour of stainless steels on member capacity , 2000 .

[22]  Kim J.R. Rasmussen,et al.  Numerical modelling of stainless steel plates in compression , 2003 .