The influence of abrasive size on high-pressure chemical mechanical polishing of sapphire wafer

Demand for sapphire wafer has increased with growth of LED market. Chemical mechanical polishing (CMP) comprises a large part of wafering cost since the CMP process requires approximately 3–6 hours. For longer polishing times, the cost of consumables (COC) in CMP increases the total wafering cost; hence, considerable efforts have been made to decrease the polishing time of sapphire wafers to reduce the COC. There are two main approaches to reduce polishing time: controlling the chemical factor and adjusting the mechanical factor. Controlling the chemical factor is a common approach to manipulating the removal rate and roughness. However, it is hard to control the chemical factor. Instead, this study investigates the effects of various mechanical factors. This paper focuses on the effect of high-pressure CMP on the material removal performance; the maximum applied pressure is ∼800 g/cm2. The removal rate increases linearly with gradual increase of CMP pressure to 800 g/cm2. Finally, the effect of high pressure on the removal rate of, and frictional force on, sapphire wafer during CMP using different sized abrasives is investigated; the effect of the abrasives on the removal rate is likewise analyzed at different pressures.

[1]  Hojun Lee,et al.  Analysis of removal mechanism on oxide CMP using mixed abrasive slurry , 2015 .

[2]  Zhitang Song,et al.  Planarization machining of sapphire wafers with boron carbide and colloidal silica as abrasives , 2009 .

[3]  Goodarz Ahmadi,et al.  A Model for Mechanical Wear and Abrasive Particle Adhesion during the Chemical Mechanical Polishing Process , 2001 .

[4]  Uday Mahajan,et al.  Effect of Particle Size during Tungsten Chemical Mechanical Polishing , 1999 .

[5]  R. Sabia,et al.  Chemical mechanical polishing (CMP) anisotropy in sapphire , 2004 .

[6]  S. C. Wang,et al.  Dichromatic InGaN-based white light emitting diodes by using laser lift-off and wafer-bonding schemes , 2007 .

[7]  Eun-Sang Lee,et al.  A study on the characteristics of a wafer-polishing process according to machining conditions , 2009 .

[8]  S. Babu,et al.  The use of monodispersed colloids in the polishing of copper and tantalum. , 2003, Journal of Colloid and Interface Science.

[9]  Marius K. Orlowski,et al.  Combined asperity contact and fluid flow model for chemical-mechanical polishing , 1994, Proceedings of International Workshop on Numerical Modeling of processes and Devices for Integrated Circuits: NUPAD V.

[10]  Yuling Liu,et al.  Method of surface treatment on sapphire substrate , 2006 .

[11]  Haedo Jeong,et al.  Effect of Process Parameters on Material Removal Rate in Chemical Mechanical Polishing of 6H-SiC(0001) , 2008 .

[12]  T. Moustakas,et al.  High power ultraviolet light emitting diodes based on GaN∕AlGaN quantum wells produced by molecular beam epitaxy , 2006 .

[13]  Zhaowei Zhong,et al.  Effects of chemical slurries on fixed abrasive chemical-mechanical polishing of optical silicon substrates , 2013 .

[14]  W. Tseng,et al.  Microstructure-related resistivity change after chemical–mechanical polish of Al and W thin films , 2000 .

[15]  T. Okamoto,et al.  Chemical planarization of GaN using hydroxyl radicals generated on a catalyst plate in H2O2 solution , 2008 .

[16]  B. Moudgil,et al.  Effect of Particle Size of Chemical Mechanical Polishing Slurries for Enhanced Polishing with Minimal Defects , 2000 .

[17]  Abhijit Chandra,et al.  A plasticity-based model of material removal in chemical-mechanical polishing (CMP) , 2001 .