Electrochromic device response controlled by an in situ polymerized ionic liquid based gel electrolyte

Polymer electrolytes were synthesized by two different approaches and applied to electrochromic devices based on electrodeposited tungsten oxide (WO3) or poly(3,4-ethylenedioxythiophene) (PEDOT) films as the cathode, and a Prussian blue (PB) film as the anode. The first method involved the entrapping of an ionic liquid in a polymer host (poly(methylmethacrylate) or PMMA) and the second approach relied on the in situ thermal polymerization of methylmethacrylate (MMA) in the hydrophobic ionic liquid, yielding a solidified transparent gel. The effect of in situ solid polymer electrolyte formation on device performance characteristics was realized in terms of a larger coloration efficiency of 119 cm2 C−1 (λ = 550 nm) achieved for the WO3–PB (MMA) device, as compared to a value of 54 cm2 C−1 obtained for the WO3–PB (PMMA) device. Similar enhancements in electrochromic coloring efficiency, reflectance contrast, and faster switching kinetics were obtained for the PEDOT–PB (MMA) device. The strategy of introducing an electrolyte to the electrochromic device in a liquid state and then subjecting the same to gradual polymerization allows greater accessibility of the electrolyte ions to the active sites on the electrochromic electrodes and superior interfacial contact. As a consequence, larger optical contrast and faster kinetics are achieved in the MMA based devices. While PEDOT films were amorphous, PB films were semi-crystalline but only in the case of WO3; the hexagonal structure of WO3, equipped with three/four/six-coordinated voids was found to affect bleaching kinetics favorably. The performance of PMMA based electrolyte is limited by high resistance at the electrode–electrolyte interface, and a smaller number of ions available for oxidation and reduction. Large area (∼10 cm × 4 cm) devices were also fabricated using this simple wet chemistry method and their ability to color uniformly without any pinholes was demonstrated.

[1]  M. Döbbelin,et al.  Synthesis of Pyrrolidinium-Based Poly(ionic liquid) Electrolytes with Poly(ethylene glycol) Side Chains , 2012 .

[2]  M. Delville,et al.  Electrochromic devices based on in situ polymerised EDOT and Prussian Blue: influence of transparent conducting oxide and electrolyte composition—towards up-scaling , 2011 .

[3]  K. Ho,et al.  A complementary electrochromic device based on Prussian blue and poly(ProDOT-Et2) with high contrast and high coloration efficiency , 2011 .

[4]  Chien A. Nguyen,et al.  Layer-by-Layer Assembled Solid Polymer Electrolyte for Electrochromic Devices , 2011 .

[5]  Pierre M Beaujuge,et al.  Material strategies for black-to-transmissive window-type polymer electrochromic devices. , 2011, ACS applied materials & interfaces.

[6]  Anne C. Dillon,et al.  Metal-oxide films for electrochromic applications: present technology and future directions , 2010 .

[7]  A. Nogueira,et al.  Electrochromic devices based on poly(3-methylthiophene) and various secondary electrochromic materials , 2010 .

[8]  M. Deepa,et al.  A dual electrochrome of poly-(3,4-ethylenedioxythiophene) doped by N,N'-bis(3-sulfonatopropyl)-4-4'-bipyridinium--redox chemistry and electrochromism in flexible devices. , 2010, ChemSusChem.

[9]  Tae-Young Lim,et al.  Cycle test and degradation analysis of WO3/PC+LiClO4/CeO2·TiO2 electrochromic device , 2009 .

[10]  J. Tu,et al.  An all-solid-state electrochromic device based on NiO/WO3 complementary structure and solid hybrid polyelectrolyte , 2009 .

[11]  M. Deepa,et al.  Electrochemistry of poly(3,4-ethylenedioxythiophene)-polyaniline/ Prussian blue electrochromic devices containing an ionic liquid based gel electrolyte film. , 2009, Physical chemistry chemical physics : PCCP.

[12]  Xuehong Lu,et al.  Toward electrochromic device using solid electrolyte with polar polymer host. , 2009, The journal of physical chemistry. B.

[13]  Xuehong Lu,et al.  A complementary electrochromic device based on polyaniline-tethered polyhedral oligomeric silsesquioxane and tungsten oxide , 2009 .

[14]  S. Balaji,et al.  Hexagonal Tungsten Oxide Based Electrochromic Devices: Spectroscopic Evidence for the Li Ion Occupancy of Four-Coordinated Square Windows , 2009 .

[15]  Marie Sedlaříková,et al.  Electrochromic devices employing methacrylate-based polymer electrolytes , 2009 .

[16]  S. L. Agrawal,et al.  Electrochromic performance of a poly(3,4-ethylenedioxythiophene)-Prussian blue device encompassing a free standing proton electrolyte film , 2008 .

[17]  Jinmin Wang,et al.  Synthesis, Assembly, and Electrochromic Properties of Uniform Crystalline WO3 Nanorods , 2008 .

[18]  S. Cho,et al.  Fast electrochemistry of conductive polymer nanotubes: synthesis, mechanism, and application. , 2008, Accounts of chemical research.

[19]  Frédéric Vidal,et al.  Self-supported semi-interpenetrating polymer networks for new design of electrochromic devices , 2008 .

[20]  David R. Rosseinsky,et al.  Electrochromism and Electrochromic Devices , 2007 .

[21]  Govind,et al.  Electro-optical response of tungsten oxide thin film nanostructures processed by a template-assisted electrodeposition route , 2007 .

[22]  Gunnar A. Niklasson,et al.  Electrochromics for smart windows: thin films of tungsten oxide and nickel oxide, and devices based on these , 2007 .

[23]  J. Reynolds,et al.  In situ colorimetric and composite coloration efficiency measurements for electrochromic Prussian blue , 2005 .

[24]  S. Kirchmeyer,et al.  Scientific importance, properties and growing applications of poly(3,4-ethylenedioxythiophene) , 2005 .

[25]  Ivan P. Parkin,et al.  Atmospheric Pressure Chemical Vapor Deposition of Crystalline Monoclinic WO3 and WO3-x Thin Films from Reaction of WCl6 with O-Containing Solvents and Their Photochromic and Electrochromic Properties , 2005 .

[26]  K. Takagi,et al.  Electrochemical properties of novel ionic liquids for electric double layer capacitor applications , 2004 .

[27]  John R. Reynolds,et al.  Microporous Patterned Electrodes for Color-Matched Electrochromic Polymer Displays , 2004 .

[28]  J. Reynolds,et al.  The First Truly All‐Polymer Electrochromic Devices , 2003 .

[29]  Dean M. DeLongchamp,et al.  Layer-by-layer assembly of PEDOT/polyaniline electrochromic devices , 2001 .

[30]  N. Grobert,et al.  Generation of hollow crystalline tungsten oxide fibres , 2000 .

[31]  J. Reynolds,et al.  Conducting Poly(3,4-alkylenedioxythiophene) Derivatives as Fast Electrochromics with High-Contrast Ratios , 1998 .

[32]  Zuhong Lu,et al.  An all-solid-state electrochromic display device of prussian blue and WO3 particulate film with a PMMA gel electrolyte , 1997 .