Optimal Scheme for Structural Design of Large Turbogenerator Stator End Winding

A three-dimensional (3-D) electromagnetic model of the end region of a 600 MW turbogenerator is set up. The variations of electromagnetic force densities of the stator end winding under rated load and three-phase short circuit from full load are obtained by numerical simulation. Then, the electromagnetic forces varying with time and space on the end winding are applied to the 3-D fine finite-element model established in ABAQUS/CAE for structural analysis, and the deformation and stress distributions of the stator end winding during rated load and three-phase short circuit are numerically analyzed by means of the ABAQUS software. Furthermore, the influences of structural and material parameters of the end winding on its dynamic responses under rated load are numerically investigated. Based on the numerical results, an optimal scheme for the design of the turbogenerator stator end winding is proposed.

[1]  S. Kulig,et al.  ELECTROMAGNETIC FORCES AND MECHANICAL OSCILLATIONS OF THE STATOR END WINDING OF TURBO GENERATORS , 2006 .

[2]  Shuting Wan,et al.  INVESTIGATION ON ELECTROMAGNETIC FORCES AND EXPERIMENTAL VIBRATION CHARACTERISTICS OF STATOR END WINDINGS IN GENERATOR , 2014 .

[3]  S. Salon,et al.  Electromagnetic Forces on the Armature End Windings of Large Turbine Generators I - Steady State Conditions , 1981, IEEE Transactions on Power Apparatus and Systems.

[4]  N. Richard.  Calculation of electromagnetic forces on large generator end-windings under fault conditions using a three-dimensional finite element method , 1998 .

[5]  Xuhui Wen,et al.  Calculation of forces on the stator end windings of turbogenerator by the transient quasi-3D method , 1996 .

[6]  Yujing Liu,et al.  Analysis of forces on coil ends of formed stator windings , 2007, 2007 International Conference on Electrical Machines and Systems (ICEMS).

[7]  A. Formisano,et al.  Coupled Three Dimensional Numerical Calculation of Forces and Stresses on the End Windings of Large Turbo Generators via Integral Formulation , 2012, IEEE Transactions on Magnetics.

[8]  S. Salon,et al.  Electromagnetic Forces on the End Windings of Large Turbine Generators. II. Transient Conditions , 1983, IEEE Transactions on Power Apparatus and Systems.

[9]  Ki-Chan Kim,et al.  Analysis of electromagnetic force distribution on end winding for motor reliance , 2005, INTERMAG Asia 2005. Digests of the IEEE International Magnetics Conference, 2005..

[10]  F. Duffeau,et al.  Computation of forces and stresses on generator end windings using a 3D finite element method , 1996 .

[11]  H. Yamaguchi,et al.  Mechanical Behavior of Stator Endwindings , 1980, IEEE Transactions on Power Apparatus and Systems.

[12]  Antero Arkkio,et al.  End-Winding Vibrations Caused by Steady-State Magnetic Forces in an Induction Machine , 2010, IEEE Transactions on Magnetics.

[13]  Bo Yan,et al.  Parametric Study on Dynamic Characteristics of Turbogenerator Stator End Winding , 2014, IEEE Transactions on Energy Conversion.

[14]  Dean Harrington.  Forces in machine end windings , 1953, Electrical Engineering.

[15]  Fabrizio Marignetti,et al.  Electromechanical analysis of end windings in turbo generators , 2011 .

[16]  S. Exnowski.  Excitability of different modes of vibration of stator end windings , 2012, IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society.

[17]  O. Drubel,et al.  End winding deformations in different turbo generators during 3-phase short circuit and full load operation , 2000 .

[18]  G. W. Buckley,et al.  Calculation of Forces and Stresses on Generator End-Windings-Part I: Forces , 1989, IEEE Power Engineering Review.

[19]  J. F. Calvert.  Forces in Turbine Generator Stator Windings , 1931, Transactions of the American Institute of Electrical Engineers.