Actuation Requirements of a Warp-Induced Variable Twist Rotor Blade

This article examines a warp-induced twist concept to obtain quasi-static large amplitude twist changes of helicopter or tiltrotor blades for performance benefits over diverse operating conditions. The presented concept has a cylindrical spar with rotating ribs which are attached to the blade skin that is slit along the trailing edge. Warping the skin then produces twisting of the blade section. Warp actuation is implemented by rotating a threaded rod assembly attached to the interior of the upper and lower skin near the trailing edge. Due to the slit at the trailing edge, the blade is soft in torsion during actuation, but is effectively a closed section due to the threaded rod assembly when in power off state. A prototype (NACA 0012, 10.75 in chord, 42 in span) based on this concept was built and tested for both the warp-twist relationship and the actuation torque requirements for producing the twist of the blade (up to ±18°). The finite element model developed in this article correlated very well with the experimental measurements made on the prototype. The validated finite element model is further used to conduct a study to understand the effect of various structural parameters on the system behavior.

[1]  Inderjit Chopra,et al.  CHARACTERIZATION OF SMA TORSIONAL ACTUATORS FOR ACTIVE TWIST OF TILT ROTOR BLADES , 2002 .

[2]  Dan Clingman,et al.  Shape Memory Alloy Consortium and demonstration , 2000 .

[3]  Heli Div.,et al.  Rotor Design Using Smart Materials to Actively Twist Blades , 1996 .

[4]  Carlos E. S. Cesnik,et al.  Modeling, design, and testing of the NASA/Army/MIT active twist rotor prototype blade , 1999 .

[5]  Andreas Paul Friedrich Bernhard.  Smart helicopter rotor with active blade tips , 2000 .

[6]  Edward C. Smith,et al.  Induced-Shear Piezoelectric Actuators for Active Twist Rotor Blades , 2002 .

[7]  A. Dean Jacot,et al.  Shape memory actuator systems and the use of thermoelectric modules , 2002, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[8]  Harsha Prahlad.  Development of shape memory alloy (SMA) torsional actuators for variable twist tilt rotor (VTTR) blades , 2002 .

[9]  Carlos E. S. Cesnik,et al.  On the twist performance of a multiple-cell active helicopter blade , 2001 .

[10]  Robert T. Ruggeri,et al.  Wind Tunnel Testing of a Lightweight ¼-Scale Actuator Utilizing Shape Memory Alloy , 2008 .

[11]  Zafer Gürdal,et al.  A Novel Mechanism for Wing Warping , 2008 .

[12]  Carlos E. S. Cesnik,et al.  Optimum Design Framework for Integrally Twisted Helicopter Blades , 2004 .

[13]  Ephraim Gutmark,et al.  Performance Predictions of a Blade Twist Actuator System , 2007 .

[14]  Carlos E. S. Cesnik,et al.  Vibratory loads reduction testing of the NASA/Army/MIT active twist rotor , 2001 .

[15]  Steven R. Schmid,et al.  Fundamentals of Machine Elements , 1999 .

[16]  Inderjit Chopra,et al.  Design of a variable twist tilt-rotor blade using shape memory alloy (SMA) actuators , 2001, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[17]  Johannes Riemenschneider,et al.  OVERVIEW OF THE COMMON DLR/ONERA PROJECT "ACTIVE TWIST BLADE" (ATB) , 2004 .

[18]  I. Chopra,et al.  Induced strain actuation of composite beams and rotor blades with embedded piezoceramic elements , 1996 .

[19]  Carlos E. S. Cesnik,et al.  HOVER TESTING OF THE NASA/ARMY/MIT ACTIVE TWIST ROTOR PROTOTYPE BLADE , 2000 .

[20]  Mihir Mistry,et al.  Twist Control of an I-beam through Vlasov Bimoment Actuation , 2008 .

[21]  Carlos E. S. Cesnik,et al.  Optimization design framework for integrally twisted helicopter blades , 2004 .

[22]  Matthew L. Wilbur,et al.  FURTHER EXAMINATION OF THE VIBRATORY LOADS REDUCTION RESULTS FROM THE NASA/ARMY/MIT ACTIVE TWIST ROTOR TEST , 2002 .

[23]  V. Vlasov.  Thin-walled elastic beams , 1961 .

[24]  Mihir Mistry.  Induced warp systems to obtain Active twist of Rotor Blades , 2008 .