Optimal design of flywheels using an injection island genetic algorithm

This paper presents an approach to optimal design of elastic flywheels using an Injection Island Genetic Algorithm (iiGA), summarizing a sequence of results reported in earlier publications. An iiGA in combination with a structural finite element code is used to search for shape variations and material placement to optimize the Specific Energy Density (SED, rotational energy per unit weight) of elastic flywheels while controlling the failure angular velocity. iiGAs seek solutions simultaneously at different levels of refinement of the problem representation (and correspondingly different definitions of the fitness function) in separate subpopulations (islands). Solutions are sought first at low levels of refinement with an axi-symmetric plane stress finite element code for high-speed exploration of the coarse design space. Next, individuals are injected into populations with a higher level of resolution that use an axi-symmetric three-dimensional finite element code to “fine-tune” the structures. A greatly simplified design space (containing two million possible solutions) was enumerated for comparison with various approaches that include: simple GAs, threshold accepting (TA), iiGAs and hybrid iiGAs. For all approaches compared for this simplified problem, all variations of the iiGA were found to be the most efficient. This paper will summarize results obtained studying a constrained optimization problem with a huge design space approached with parallel GAs that had various topological structures and several different types of iiGA, to compare efficiency. For this problem, all variations of the iiGA were found to be extremely efficient in terms of computational time required to final solution of similar fitness when compared to the parallel GAs.

[1]  Erik D. Goodman,et al.  Coarse-grain parallel genetic algorithms: categorization and new approach , 1994, Proceedings of 1994 6th IEEE Symposium on Parallel and Distributed Processing.

[2]  Subramaniam Rajan,et al.  Sizing, Shape, and Topology Design Optimization of Trusses Using Genetic Algorithm , 1995 .

[3]  Erik D. Goodman,et al.  Optimal design of laminated composite structures using coarse-grain parallel genetic algorithms , 1994 .

[4]  Prabhat Hajela,et al.  Topological optimization of rotorcraft subfloor structures for crashworthiness considerations , 1997 .

[5]  Erik D. Goodman,et al.  Parallel Genetic Algorithms in the Optimization of Composite Structures , 1998 .

[6]  Nestor V. Queipo,et al.  Genetic algorithms for thermosciences research: application to the optimized cooling of electronic components , 1994 .

[7]  Ian C. Parmee,et al.  Co-operative Evolutionary Strategies for Single Component Design , 1997, ICGA.

[8]  Shigeru Nakagiri,et al.  Optimization of Frame Topology Using Boundary Cycle and Genetic Algorithm , 1996 .

[9]  Alejandro R. Diaz,et al.  Optimum Layout and Shape of Plate Structures Using Homogenization , 1993 .

[10]  J. Haslinger,et al.  Genetic algorithms and fictitious domain based approaches in shape optimization , 1996 .

[11]  Cecilia Surace,et al.  An application of Genetic Algorithms to identify damage in elastic structures , 1996 .

[12]  Jens von Wolfersdorf,et al.  Shape Optimization of Cooling Channels Using Genetic Algorithms , 1997 .

[13]  Erik D. Goodman,et al.  Using Genetic Algorithms to Design Laminated Composite Structures , 1995, IEEE Expert.

[14]  Hideo Kobayashi,et al.  Application of Genetic Algorithms to Stiffness Optimization of Laminated Composite Plates with Stress-Concentrated Open Holes , 1995 .

[15]  Giancarlo Genta,et al.  Use of genetic algorithms for the design of rotors , 1995 .

[16]  Andy J. Keane,et al.  Passive vibration control via unusual geometries: the application of genetic algorithm optimization to structural design , 1995 .

[17]  Robert Flynn,et al.  Multicriteria optimization of aircraft panels: Determining viable genetic algorithm configurations , 1995, Int. J. Intell. Syst..

[18]  C. G. Shaefer,et al.  The ARGOT Strategy: Adaptive Representation Genetic Optimizer Technique , 1987, ICGA.

[19]  M. Jakiela,et al.  Genetic algorithm-based structural topology design with compliance and topology simplification considerations , 1996 .

[20]  Nozomu Kogiso,et al.  Genetic algorithms with local improvement for composite laminate design , 1993 .

[21]  G. Fabbri.  A genetic algorithm for fin profile optimization , 1997 .

[22]  R. Haftka,et al.  Optimization of laminate stacking sequence for buckling load maximization by genetic algorithm , 1993 .

[23]  Hiroshi Furuya,et al.  Placing actuators on space structures by genetic algorithms and effectiveness indices , 1995 .

[24]  Rob A. Rutenbar,et al.  Simulated annealing algorithms: an overview , 1989, IEEE Circuits and Devices Magazine.

[25]  N. Kikuchi,et al.  A homogenization method for shape and topology optimization , 1991 .

[26]  George S. Dulikravich,et al.  Three-Dimensional Aerodynamic Shape Optimization Using Genetic and Gradient Search Algorithms , 1997 .

[27]  E Sandgren,et al.  TOPOLOGICAL DESIGN OF STRUCTURAL COMPONENTS USING GENETIC OPTIMIZATION METHOD , 1990 .