Micro Tooling Design and Manufacturing

[1]  Muhammad Ekhlasur Rahman,et al.  Experimental study of micro- and nano-scale cutting of aluminum 7075-T6 , 2006 .

[2]  Paul Mativenga,et al.  Evaluation and selection of hard coatings for micro milling of hardened tool steel , 2008 .

[3]  P. Kelly,et al.  Magnetron sputtering: a review of recent developments and applications , 2000 .

[4]  H. Weule,et al.  Micro-Cutting of Steel to Meet New Requirements in Miniaturization , 2001 .

[5]  A. Moufki,et al.  A review of developments towards dry and high speed machining of Inconel 718 alloy , 2004 .

[6]  Kai Egashira,et al.  Micro-drilling of monocrystalline silicon using a cutting tool , 2002 .

[7]  Lothar Bohn,et al.  Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills , 1999 .

[8]  John W. Sutherland,et al.  Dry Machining and Minimum Quantity Lubrication , 2004 .

[9]  H. Holleck.  Material selection for hard coatings , 1986 .

[10]  Z. Qin,et al.  Tool wear characteristics in high-speed milling of graphite using a coated carbide micro endmill , 2009 .

[11]  Kai Cheng,et al.  Experimental investigation on micromilling of oxygen-free, high-conductivity copper using tungsten carbide, chemistry vapour deposition, and single-crystal diamond micro tools , 2010 .

[12]  W. M. Rainforth,et al.  TEM observations of wear mechanisms of TiAlCrN and TiAlN/CrN coatings grown by combined steered-arc/unbalanced magnetron deposition , 1999 .

[13]  Paul Mativenga,et al.  Size effect and tool geometry in micromilling of tool steel , 2009 .

[14]  Paul Mativenga,et al.  Estimation of minimum chip thickness in micro-milling using acoustic emission , 2011 .

[15]  Iwao Miyamoto,et al.  Ion beam machining of single-point diamond tools for nano-precision turning , 1990 .

[16]  Kai Cheng,et al.  Design and analysis of a piezoelectric film embedded smart cutting tool , 2013 .

[17]  Gwo-Lianq Chern,et al.  Study on burr formation in micro-machining using micro-tools fabricated by micro-EDM , 2007 .

[18]  P. Mativenga,et al.  Identification of factors that dominate size effect in micro-machining , 2011 .

[19]  I. Efeoglu,et al.  Deposition of graded alloy nitride films by closed field unbalanced magnetron sputtering , 1993 .

[20]  W. M. Rainforth,et al.  Tribological investigation of TiAlCrN and TiAlN/CrN coatings grown by combined steered-arc/unbalanced magnetron deposition , 1999 .

[21]  Craig R. Friedrich.  Micromechanical machining of high aspect ratio prototypes , 2002 .

[22]  G. L. Benavides,et al.  Micromilling of metal alloys with focused ion beam–fabricated tools , 1999 .

[23]  J. Gäbler,et al.  Precision and micro CVD diamond-coated grinding tools , 2010 .

[24]  Konstantinos-Dionysios Bouzakis,et al.  Improvement of PVD coated inserts cutting performance, through appropriate mechanical treatments of substrate and coating surface , 2001 .

[25]  Dermot Geraghty,et al.  The Development of Surface Acoustic Wave Sensors (SAWs) for Process Monitoring , 2012 .

[26]  Shuliang Dong,et al.  Effect of diamond tool sharpness on minimum cutting thickness and cutting surface integrity in ultraprecision machining , 1996 .

[27]  Craig R. Friedrich,et al.  Micrometer-scale machining: tool fabrication and initial results , 1996 .