Influence of infill properties on flexural rigidity of 3D-printed structural members

ABSTRACT This paper characterises the flexural properties of relatively slender structural members (beams) manufactured using a FDM-based 3D printer. The primary goal is to assess the influence of infill properties on flexural rigidity through a parametric investigation. Infill percentage, infill orientation, and member thickness provided the parametric variation. The beams were tested by three-point bending, free vibration, and buckling. The tests showed that flexural rigidity varied linearly with infill percentage over most of the range considered, but fell off quickly below 10% infill. The optimal infill percentage that maximised specific flexural rigidity (flexural rigidity to length density) of the beams was determined to be between 10% and 20%.

[1]  Ming-Chuan Leu,et al.  Progress in Additive Manufacturing and Rapid Prototyping , 1998 .

[2]  V. H. Nam,et al.  Nonlinear dynamical analysis of eccentrically stiffened functionally graded cylindrical panels , 2012 .

[3]  Lawrence N. Virgin,et al.  On the flexural stiffness of 3D printer thermoplastic , 2017 .

[4]  Ian Gibson,et al.  Augmented patient-specific facial prosthesis production using medical imaging modelling and 3D printing technologies for improved patient outcomes , 2018 .

[5]  Lawrence N. Virgin,et al.  Enhancing the teaching of structural dynamics using additive manufacturing , 2017 .

[6]  Aurelian Zapciu,et al.  FDM process parameters influence over the mechanical properties of polymer specimens: A review , 2018, Polymer Testing.

[7]  Albert J. Shih,et al.  Additive manufacturing of custom orthoses and prostheses-A review , 2016 .

[8]  Erdal Kayacan,et al.  Evaluation of the influence of build and print orientations of unmanned aerial vehicle parts fabricated using fused deposition modeling process , 2018, Journal of Manufacturing Processes.

[9]  W. C. Smith,et al.  Structural characteristics of fused deposition modeling polycarbonate material , 2013 .

[10]  Bruce L. Tai,et al.  Bending behaviors of 3D-printed Bi-material structure: Experimental study and finite element analysis , 2017 .

[11]  Lawrence N. Virgin,et al.  Enhancing the teaching of linear structural analysis using additive manufacturing , 2017 .

[12]  Chiara Daraio,et al.  Tensile Properties of Inkjet 3D Printed Parts: Critical Process Parameters and Their Efficient Analysis , 2015 .

[13]  C KennyLAlvarez,et al.  Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts , 2016 .

[14]  E. García-Plaza,et al.  Additive manufacturing of PLA structures using fused deposition modelling: Effect of process parameters on mechanical properties and their optimal selection , 2017 .

[15]  Marek Gasior,et al.  Improving FFT Frequency Measurement Resolution by Parabolic and Gaussian Spectrum Interpolation , 2004 .

[16]  Alejandro H. Espera,et al.  Mechanical characterization of 3D-printed polymers , 2018 .

[17]  P. S. Harvey,et al.  Effect of Stiffener Geometry on the Response of Grid-Stiffened Panels , 2018 .

[18]  Srinivasa Prakash Regalla,et al.  Multi-objective optimisation of strength and volumetric shrinkage of FDM parts , 2014 .

[19]  C. Perkowski.  Tensile-Compressive Asymmetry and Anisotropy of Fused Deposition Modeling PLA under Monotonic Conditions , 2017 .

[20]  T. Schaedler,et al.  Architected Cellular Materials , 2016 .

[21]  Gregory Taylor,et al.  Experimental investigation of effects of build parameters on flexural properties in fused deposition modelling parts , 2017 .

[22]  Ognjan B. Lu,et al.  EFFECT OF LAYER THICKNESS, DEPOSITION ANGLE, AND INFILL ON MAXIMUM FLEXURAL FORCE IN FDM-BUILT SPECIMENS , 2014 .

[23]  S. Vinodh,et al.  A review on composite materials and process parameters optimisation for the fused deposition modelling process , 2017 .

[24]  Joshua M. Pearce,et al.  The effects of PLA color on material properties of 3-D printed components , 2015 .

[25]  Sheng-Jen Hsieh,et al.  Modelling and estimation of tensile behaviour of polylactic acid parts manufactured by fused deposition modelling using finite element analysis and knowledge-based library , 2018 .