Effect of aluminum closed-cell foam filling on the quasi-static axial crush performance of glass fiber reinforced polyester composite and aluminum/composite hybrid tubes

The effect of Al closed-cell foam filling on the quasi-static crushing behavior of an E-glass woven fabric polyester composite tube and thin-walled Al/polyester composite hybrid tube was experimentally investigated. For comparison, empty Al, empty composite and empty hybrid tubes were also tested. Empty composite and empty hybrid tubes crushed predominantly in progressive crushing mode, without applying any triggering mechanism. Foam filling was found to be ineffective in increasing the crushing loads of the composite tubes over the sum of the crushing loads of empty composite tube and foam. However, foam filling stabilized the composite progressive crushing mode. In empty hybrid tubes, the deformation mode of the inner Al tube was found to be a more complex form of the diamond mode of deformation of empty Al tube, leading to higher crushing load values than the sum of the crushing load values of empty composite tube and empty metal tube. The foam filling of hybrid tubes however resulted in axial splitting of the outer composite tube due to the resistance imposed by the foam filler to Al tube inward folding and hence it was ineffective in increasing crushing load and SAE values over those of empty hybrid tubes.

[1]  O. Hopperstad,et al.  Static and dynamic crushing of square aluminium extrusions with aluminium foam filler , 2000 .

[2]  T. Y. Reddy,et al.  Axial compression of foam-filled thin-walled circular tubes , 1988 .

[3]  S. Yüksel,et al.  SiC-particulate aluminum composite foams produced from powder compacts: foaming and compression behavior , 2006 .

[4]  Michael F. Ashby,et al.  Energy absorption of foam-filled circular tubes with braided composite walls , 2000 .

[5]  M. Jiménez,et al.  Effect of trigger geometry on energy absorption in composite profiles , 2000 .

[6]  Chris D. Rudd,et al.  The influence of processing variables on the energy absorption of composite tubes , 2005 .

[7]  S. Ramakrishna.  MICROSTRUCTURAL DESIGN OF COMPOSITE MATERIALS FOR CRASHWORTHY STRUCTURAL APPLICATIONS , 1997 .

[8]  T. Lu,et al.  Dynamic crashing and impact energy absorption of 3D braided composite tubes , 2005 .

[9]  S. Reid,et al.  Static and dynamic axial crushing of foam-filled sheet metal tubes , 1986 .

[10]  Tomasz Wierzbicki,et al.  Crash behavior of box columns filled with aluminum honeycomb or foam , 1998 .

[11]  Chang-Hsuan Chiu,et al.  Effects of Braiding Parameters on Energy Absorption Capability of Triaxially Braided Composite Tubes , 1998 .

[12]  H. Kavi,et al.  Predicting energy absorption in a foam-filled thin-walled aluminum tube based on experimentally determined strengthening coefficient , 2006 .

[13]  T. Wierzbicki,et al.  Experimental and numerical studies of foam-filled sections , 2000 .

[14]  Mustafa Güden,et al.  The strengthening effect of polystyrene foam filling in aluminum thin-walled cylindrical tubes , 2005 .

[15]  R. A. Jeryan,et al.  Effectiveness of Polyurethane Foam in Energy Absorbing Structures , 1982 .

[16]  Chris D. Rudd,et al.  Effect of resin properties and processing parameters on crash energy absorbing composite structures made by RTM , 2003 .

[17]  Norman A. Fleck,et al.  Deformation and failure mechanisms of braided composite tubes in compression and torsion , 2000 .

[18]  F. Rammerstorfer,et al.  Experimental studies on the quasi-static axial crushing of steel columns filled with aluminium foam , 2000 .

[19]  Chris D. Rudd,et al.  The effect of interlaminar toughening strategies on the energy absorption of composite tubes , 2004 .

[20]  G. Lu,et al.  Quasi-static axial compression of thin-walled circular aluminium tubes , 2001 .

[21]  H. Hamada,et al.  Basic Study of Progressive Crushing Mechanism , 2000 .

[22]  Seeram Ramakrishna,et al.  Energy Absorption Characteristics of Crash Worthy Structural Composite Materials , 1997 .

[23]  A. A. Singace.  Collapse behaviour of plastic tubes filled with wood sawdust , 2000 .

[24]  P. H. Thornton.  ENERGY ABSORPTION BY FOAM FILLED STRUCTURES , 1980 .

[25]  Kum Cheol Shin,et al.  Axial crush and bending collapse of an aluminum/GFRP hybrid square tube and its energy absorption capability , 2001 .

[26]  P. K. Mallick,et al.  Static axial crush performance of unfilled and foam-filled aluminum–composite hybrid tubes , 2005 .

[27]  A. Toksoy,et al.  Effect of adhesive on the strengthening of aluminum foam-filled circular tubes , 2004 .