Preparation of active layers in polymer solar cells by aerosol jet printing.

Active layers of polymer solar cells were prepared by aerosol jet printing of organic inks. Various solvents and additives with high boiling points were screened for the preparation of high-quality polymer films. The effects on device performance of treating the films by thermal and solvent vapor annealing were also investigated. The components of the solvent were important for controlling the drying rate of the liquid films, reducing the number of particle-like protrusions on the film surface, and realizing high molecular ordering in the polymer phases. The optimized solar cell device with poly(3-hexylthiophene) and a C(60) derivative showed a high fill factor of 67% and power conversion efficiency of 2.53% without thermal annealing. The combination of poly[N-9-heptadecanyl-2,7-carbazole-alt-3,6-bis(thiophen-5-yl)-2,5-diethylhexyl-2,5-dihydropyrrolo-[3,4-]pyrrole-1,4-dione] and a C(70) derivative led to power conversion efficiency of 3.92 and 3.14% for device areas of 0.03 and 1 cm(2), respectively.

[1]  Xiaoniu Yang,et al.  Toward High-Performance Polymer Solar Cells: The Importance of Morphology Control , 2007 .

[2]  Shinuk Cho,et al.  Bulk heterojunction solar cells based on a low-bandgap carbazole-diketopyrrolopyrrole copolymer , 2010 .

[3]  Jan Fyenbo,et al.  Product integration of compact roll-to-roll processed polymer solar cell modules: methods and manufacture using flexographic printing, slot-die coating and rotary screen printing , 2010 .

[4]  Mikkel Jørgensen,et al.  Upscaling of polymer solar cell fabrication using full roll-to-roll processing. , 2010, Nanoscale.

[5]  Yun Zhao,et al.  Solvent-vapor treatment induced performance enhancement of poly(3-hexylthiophene):methanofullerene bulk-heterojunction photovoltaic cells , 2007 .

[6]  John R. Reynolds,et al.  Dithienogermole as a fused electron donor in bulk heterojunction solar cells. , 2011, Journal of the American Chemical Society.

[7]  T. Dupont,et al.  Capillary flow as the cause of ring stains from dried liquid drops , 1997, Nature.

[8]  Gang Li,et al.  Control of the nanoscale crystallinity and phase separation in polymer solar cells , 2008 .

[9]  J. Ding,et al.  Development of a new s-tetrazine-based copolymer for efficient solar cells. , 2010, Journal of the American Chemical Society.

[10]  S. Jang,et al.  Performance Optimization of Polymer Solar Cells Using Electrostatically Sprayed Photoactive Layers , 2010 .

[11]  Nagel,et al.  Contact line deposits in an evaporating drop , 2000, Physical review. E, Statistical physics, plasmas, fluids, and related interdisciplinary topics.

[12]  C. Brabec,et al.  Nanomorphology and Charge Generation in Bulk Heterojunctions Based on Low‐Bandgap Dithiophene Polymers with Different Bridging Atoms , 2010 .

[13]  Jan Genoe,et al.  Polymer based organic solar cells using ink-jet printed active layers , 2008 .

[14]  J. Schmidtke.  Commercial status of thin-film photovoltaic devices and materials. , 2010, Optics express.

[15]  Luping Yu,et al.  A new class of semiconducting polymers for bulk heterojunction solar cells with exceptionally high performance. , 2010, Accounts of chemical research.

[16]  Gang Li,et al.  Recent Progress in Polymer Solar Cells: Manipulation of Polymer:Fullerene Morphology and the Formation of Efficient Inverted Polymer Solar Cells , 2009 .

[17]  M. Doi,et al.  Final shape of a drying thin film. , 2009, Physical review. E, Statistical, nonlinear, and soft matter physics.

[18]  Gang Li,et al.  Effects of Solvent Mixtures on the Nanoscale Phase Separation in Polymer Solar Cells , 2008 .

[19]  Yang Yang,et al.  Polymer solar cells with enhanced open-circuit voltage and efficiency , 2009 .

[20]  Ye Tao,et al.  Bulk heterojunction solar cells using thieno[3,4-c]pyrrole-4,6-dione and dithieno[3,2-b:2',3'-d]silole copolymer with a power conversion efficiency of 7.3%. , 2011, Journal of the American Chemical Society.

[21]  M. Leclerc,et al.  Synthesis and Characterization of New Low-Bandgap Diketopyrrolopyrrole-Based Copolymers , 2009 .

[22]  F. Krebs,et al.  Low band gap polymers for organic photovoltaics , 2007 .

[23]  Xiong Gong,et al.  Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology , 2005 .

[24]  Yong Cao,et al.  Development of novel conjugated donor polymers for high-efficiency bulk-heterojunction photovoltaic devices. , 2009, Accounts of chemical research.

[25]  Guillermo C. Bazan,et al.  Improved Performance of Polymer Bulk Heterojunction Solar Cells Through the Reduction of Phase Separation via Solvent Additives , 2010, Advanced materials.

[26]  F. Krebs.  Fabrication and processing of polymer solar cells: A review of printing and coating techniques , 2009 .

[27]  D. S. Martyanov,et al.  Properties of MEH-PPV films prepared by slow solvent evaporation , 2004 .

[28]  Christoph J. Brabec,et al.  On the effect of poly(3-hexylthiophene) regioregularity on inkjet printed organic solar cells , 2009 .

[29]  Martin A. Green,et al.  Solar cell efficiency tables (Version 38) , 2011 .

[30]  Gang Li,et al.  “Solvent Annealing” Effect in Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Methanofullerenes , 2007 .

[31]  A J Heeger,et al.  Efficiency enhancement in low-bandgap polymer solar cells by processing with alkane dithiols. , 2007, Nature materials.

[32]  Jan Fyenbo,et al.  Manufacture, integration and demonstration of polymer solar cells in a lamp for the “Lighting Africa” initiative , 2010 .

[33]  Gang Li,et al.  Highly efficient inverted polymer solar cell by low temperature annealing of Cs2CO3 interlayer , 2008 .

[34]  Kazuhiro Saito,et al.  Origin of the open-circuit voltage of organic thin-film solar cells based on conjugated polymers , 2009 .

[35]  Claudia N. Hoth,et al.  High Photovoltaic Performance of Inkjet Printed Polymer:Fullerene Blends , 2007 .

[36]  K. Hashimoto,et al.  Synthesis and Photovoltaic Properties of Diketopyrrolopyrrole-Based Donor−Acceptor Copolymers , 2009 .

[37]  M. Leclerc,et al.  A High-Mobility Low-Bandgap Poly(2,7-carbazole) Derivative for Photovoltaic Applications , 2009 .

[38]  Christoph J. Brabec,et al.  Design Rules for Donors in Bulk‐Heterojunction Solar Cells—Towards 10 % Energy‐Conversion Efficiency , 2006 .

[39]  A. J. Heeger,et al.  Photoinduced Electron Transfer from a Conducting Polymer to Buckminsterfullerene , 1992, Science.

[40]  G. Jabbour,et al.  Inkjet Printing—Process and Its Applications , 2010, Advanced materials.

[41]  Jooho Moon,et al.  Control of colloidal particle deposit patterns within picoliter droplets ejected by ink-jet printing. , 2006, Langmuir : the ACS journal of surfaces and colloids.

[42]  J. Fréchet,et al.  Polymer-fullerene composite solar cells. , 2008, Angewandte Chemie.

[43]  U. Schubert,et al.  Inkjet printing of well-defined polymer dots and arrays. , 2004, Langmuir : the ACS journal of surfaces and colloids.

[44]  Claudia N. Hoth,et al.  Printing highly efficient organic solar cells. , 2008, Nano letters.

[45]  F. Krebs,et al.  A roll-to-roll process to flexible polymer solar cells: model studies, manufacture and operational stability studies , 2009 .

[46]  C. Brabec,et al.  Origin of the Open Circuit Voltage of Plastic Solar Cells , 2001 .

[47]  Jin Young Kim,et al.  Processing additives for improved efficiency from bulk heterojunction solar cells. , 2008, Journal of the American Chemical Society.

[48]  T. Swager,et al.  Control of conformational and interpolymer effects in conjugated polymers , 2001, Nature.

[49]  Mats Andersson,et al.  Influence of Solvent Mixing on the Morphology and Performance of Solar Cells Based on Polyfluorene Copolymer/Fullerene Blends , 2006 .

[50]  Daniel Moses,et al.  Method for increasing the photoconductive response in conjugated polymer/fullerene composites , 2006 .

[51]  Yongfang Li,et al.  6.5% Efficiency of Polymer Solar Cells Based on poly(3‐hexylthiophene) and Indene‐C60 Bisadduct by Device Optimization , 2010, Advanced materials.

[52]  Jan Fyenbo,et al.  Grid-connected polymer solar panels: initial considerations of cost, lifetime, and practicality. , 2010, Optics express.

[53]  Shinuk Cho,et al.  Effect of processing additive on the nanomorphology of a bulk heterojunction material. , 2010, Nano letters.

[54]  Yang Yang,et al.  Multi-source/component spray coating for polymer solar cells. , 2010, ACS nano.

[55]  Benjamin J. Schwartz,et al.  Conjugated polymer aggregates in solution: Control of interchain interactions , 1999 .

[56]  A. Heeger,et al.  Semiconducting polymers: the Third Generation. , 2010, Chemical Society reviews.

[57]  J. Hummelen,et al.  Polymer Photovoltaic Cells: Enhanced Efficiencies via a Network of Internal Donor-Acceptor Heterojunctions , 1995, Science.

[58]  Yang Yang,et al.  High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends , 2005 .

[59]  Martin Kumar Patel,et al.  Ex‐ante environmental and economic evaluation of polymer photovoltaics , 2009 .

[60]  Stefan W. Glunz,et al.  Metal aerosol jet printing for solar cell metallization , 2007 .

[61]  Yang Yang,et al.  Manipulating regioregular poly(3-hexylthiophene) : [6,6]-phenyl-C61-butyric acid methyl ester blends—route towards high efficiency polymer solar cells , 2007 .