An investigation of cutting forces and cutting temperatures during laser-assisted machining of the Ti–6Cr–5Mo–5V–4Al beta titanium alloy

Beta titanium alloys are increasingly attractive because of their superior combination of properties such as high strength and fracture toughness. These alloys are finding potential applications in the manufacture of aircraft components such as landing gear, springs and nacelles. Innovative machining solutions are required to reduce the cost of production of beta titanium components and improve cycle time. Previous research has reported that these alloys have poor machinability compared to the more common Ti–6Al–4V titanium alloy. This paper aims to investigate the behaviour of the Ti–6Cr–5Mo–5V–4Al beta titanium alloy using laser assisted machining (LAM). The LAM technique utilises a laser beam which is applied onto the workpiece surface locally in front of the cutting tool in order to provide external heat to significantly reduce the yield strength of the material. This reduces the cutting forces required to machine the workpiece and increases metal removal rates. In this study, the effect of the laser beam on the cutting forces and cutting temperature is critically analysed over a wide range of feed rates and cutting speeds and is compared to the results obtained from conventional (un-assisted) machining of this beta titanium alloy. This investigation has shown that LAM significantly reduces cutting forces within a certain range of cutting parameters. Maximum benefit was achieved at feed rates between 0.15 and 0.25 mm/rev and cutting speeds between 25 and 100 m/min at a laser power of 1200 W during LAM of the Ti–6Cr–5Mo–5V–4Al beta titanium alloy.

[1]  Janez Kopac,et al.  Tool wear monitoring during the turning process , 2001 .

[2]  D. Kent,et al.  Influence of ageing temperature and heating rate on the properties and microstructure of β Ti alloy, Ti–6Cr–5Mo–5V–4Al , 2012 .

[3]  P. Arrazola,et al.  Machinability of titanium alloys (Ti6Al4V and Ti555.3) , 2009 .

[4]  Vishal S. Sharma,et al.  Cooling techniques for improved productivity in turning , 2009 .

[5]  Mahmudur Rahman,et al.  Machinability of titanium alloys , 2003 .

[6]  M. Dargusch,et al.  Machinability of a near beta titanium alloy , 2011 .

[7]  Y. Shin,et al.  Machinability improvement of titanium alloy (Ti–6Al–4V) via LAM and hybrid machining , 2010 .

[8]  N. Zorev.  Metal cutting mechanics , 1966 .

[9]  M. Bermingham,et al.  A comparison of cryogenic and high pressure emulsion cooling technologies on tool life and chip morphology in Ti-6Al-4V cutting , 2012 .

[10]  R. R. Boyer,et al.  The use of β titanium alloys in the aerospace industry , 2005 .

[11]  Ronald W. Armstrong,et al.  High strain rate properties of metals and alloys , 2008 .

[12]  D. Biermann,et al.  Machining of β-titanium-alloy Ti–10V–2Fe–3Al under cryogenic conditions: Cooling with carbon dioxide snow , 2011 .

[13]  P. S. Follansbee.  Analysis of the strain-rate sensitivity at high strain rates in FCC and BCC metals , 1988 .

[14]  S. Smith,et al.  Current Trends in High-Speed Machining , 1997 .

[15]  S. Palanisamy,et al.  Effects of coolant pressure on chip formation while turning Ti6Al4V alloy , 2009 .

[16]  G. Dessein,et al.  An Experimental Investigation of Hot Machining with Induction to Improve Ti-5553 Machinability , 2011 .

[17]  Matthew S. Dargusch,et al.  Experimental investigation of cutting forces and tool wear during laser-assisted milling of Ti-6Al-4V alloy , 2011 .

[18]  M. Dargusch,et al.  Characteristics of cutting forces and chip formation in machining of titanium alloys , 2009 .

[19]  M. Dargusch,et al.  Machining Ti–6Al–4V alloy with cryogenic compressed air cooling , 2010 .

[20]  E. Ezugwu.  Key improvements in the machining of difficult-to-cut aerospace superalloys , 2005 .

[21]  James G. Harris,et al.  Parametric Investigation of Laser‐Assisted Machining of Commercially Pure Titanium , 2008 .

[22]  A. Bayram,et al.  Effects of microstructure on machinability of ductile iron , 2011 .

[23]  P. Mathew,et al.  Allowing for the influence of strain hardening in determining the frictional conditions at the tool-chip interface in machining , 1981 .

[24]  Matthew S. Dargusch,et al.  New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V , 2011 .

[25]  M. Dargusch,et al.  Thermally enhanced machining of hard-to-machine materials: a review , 2010 .

[26]  Paul S. Follansbee,et al.  An analysis of the low temperature, low and high strain-rate deformation of Ti−6Al−4V , 1989 .

[27]  Chenglong Zhang,et al.  Evaluation and Optimization Method of High Speed Cutting Parameters Based on Cutting Process Simulation , 2009, ICIRA.

[28]  G. D. Davis,et al.  A numerical method for calculating temperature distributions in machining, from force and shear angle measurements , 1976 .

[29]  V. Astakhov.  Tribology of metal cutting , 2006 .

[30]  Guillem Quintana,et al.  Chatter in machining processes: A review , 2011 .

[31]  W. F. Hastings,et al.  A machining theory for predicting chip geometry, cutting forces etc. from work material properties and cutting conditions , 1980, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.