Polycarbonate as an Elasto-Plastic Material Model for Simulation of the Microstructure Hot Imprint Process

The thermal imprint process of polymer micro-patterning is widely applied in areas such as manufacturing of optical parts, solar energy, bio-mechanical devices and chemical chips. Polycarbonate (PC), as an amorphous polymer, is often used in thermoforming processes because of its good replication characteristics. In order to obtain replicas of the best quality, the imprint parameters (e.g., pressure, temperature, time, etc.) must be determined. Therefore finite element model of the hot imprint process of lamellar periodical microstructure into PC has been created using COMSOL Multiphysics. The mathematical model of the hot imprint process includes three steps: heating, imprinting and demolding. The material properties of amorphous PC strongly depend on the imprint temperature and loading pressure. Polycarbonate was modelled as an elasto-plastic material, since it was analyzed below the glass transition temperature. The hot imprint model was solved using the heat transfer and the solid stress-strain application modes with thermal contact problem between the mold and polycarbonate. It was used for the evaluation of temperature and stress distributions in the polycarbonate during the hot imprint process. The quality of the replica, by means of lands filling ratio, was determined as well.

[1]  Jun Liu,et al.  Deformation behavior of solid polymer during hot embossing process , 2010 .

[2]  Minvydas Ragulskis,et al.  High-frequency excitation for thermal imprint of microstructures into a polymer , 2013, Experimental Techniques.

[3]  H. Meijer,et al.  The Influence of Molecular Orientation on the Yield and Post‐Yield Response of Injection‐Molded Polycarbonate , 2009 .

[4]  Xiaodi Tan,et al.  Collinear technology for a holographic versatile disk. , 2006, Applied optics.

[5]  Hiroshi Goto,et al.  Development of ultrasonic micro hot embossing technology , 2007 .

[6]  Peter Wriggers,et al.  Computational Contact Mechanics , 2002 .

[7]  Tomoyoshi Ito,et al.  Parallel computing of a digital hologram and particle searching for microdigital-holographic particle-tracking velocimetry. , 2007, Applied optics.

[8]  Dan Cojoc,et al.  Wave front engineering for microscopy of living cells. , 2005, Optics express.

[9]  A. Goel.  Thermodynamically consistent large deformation constitutive model for glassy polymers , 2009 .

[10]  M. Heckele,et al.  Review on micro molding of thermoplastic polymers , 2004 .

[11]  Bahram Javidi,et al.  Extended focused image in microscopy by digital Holography. , 2005, Optics express.

[12]  Norbert F Scherer,et al.  Stochastic scanning multiphoton multifocal microscopy. , 2006, Optics express.

[13]  C. Wilkinson,et al.  Optical heating for short hot embossing cycle times , 2006 .

[14]  Y. Hirai,et al.  Defect analysis in thermal nanoimprint lithography , 2003 .

[15]  Andrew J. Waddie,et al.  Design of diffractive optical elements for high-power laser applications , 2004 .

[16]  E. Cuche,et al.  Characterization of microlenses by digital holographic microscopy. , 2006, Applied optics.

[17]  L. Cai,et al.  Interference of four umbrellalike beams by a diffractive beam splitter for fabrication of two-dimensional square and trigonal lattices. , 2003, Optics letters.

[18]  Lingfeng Yu,et al.  Movies of cellular and sub-cellular motion by digital holographic microscopy , 2006, Biomedical engineering online.

[19]  Robert Plana,et al.  VERIFICATION OF CONTACT MODELING WITH COMSOL MULTIPHYSICS SOFTWARE , 2007 .

[20]  Jing Wang,et al.  Micromachining of SrTiO3 steps for high-Tc step edge junction dc SQUIDs , 2004 .

[21]  Matthias Worgull,et al.  Modeling and optimization of the hot embossing process for micro- and nanocomponent fabrication , 2006 .