Effect of Z Values on the Microstructure and Mechanical Properties of Post-sintered Reaction Bonded β-SiAlON

Abstract β-SiAlON materials with different Z values (Z=0.5–3) were fabricated by a reaction bonding combining post-sintering route using raw materials of Si, Al2O3, AlN, etc. The reaction bonded β-SiAlON (RB-β-SiAlON) were post-sintered at 1,750 °C for 6 h. Apparent porosity, bulk density, bending strength and Vicker’s hardness of the samples before and after post-sintering were tested. XRD results showed that the phase composition of both RB-β-SiAlON and post-sintered RB-β-SiAlON (PSRB-β-SiAlON) were β-SiAlON. For RB-β-SiAlON, the apparent porosity was decreased with the increase of Z values, while the strength and hardness was increased accordingly. After the post-sintering procedure, nearly full densified PSRB-β-SiAlON was obtained and the mechanical properties were significantly improved. The bending strength and Vicker’s hardness of the PSRB-β-SiAlON (Z=0.5) achieved 510 MPa and 16.5 GPa, respectively, which were as 2.7 and 6.7 times high as those of the corresponding RB-β-SiAlON. However, the strength and hardness of PSRB-β-SiAlON decreased with the increase of Z value due to the grain growth.

[1]  G. Qiao,et al.  Fast heating thermal shock test for β-SiAlON with molten metals as heating medium , 2015 .

[2]  Yujun Zhang,et al.  Effect of AlN content on properties of hot-press sintered Sialon ceramics , 2015 .

[3]  G. Qiao,et al.  Synthesis of β-SiAlON/h-BN nanocomposite by a precursor infiltration and pyrolysis (PIP) route , 2015 .

[4]  K. Hirao,et al.  Effects of Impurity Iron Content on Characteristics of Sintered Reaction‐Bonded Silicon Nitride , 2013 .

[5]  S. Hampshire,et al.  Pressureless sintering of β-SiAlON ceramic compositions using fluorine and oxide additive system , 2012 .

[6]  A. Kara,et al.  Effect of sintering conditions and heat treatment on the properties, microstructure and machining performance of α-β-SiAlON ceramics , 2012 .

[7]  K. Hirao,et al.  Effects of Impurity Oxygen Content in Raw Si Powder on Thermal and Mechanical Properties of Sintered Reaction‐Bonded Silicon Nitrides , 2012 .

[8]  Y. Yoshizawa,et al.  A Tough Silicon Nitride Ceramic with High Thermal Conductivity , 2011, Advanced materials.

[9]  A. Krell,et al.  Grain Size‐Dependent Hardness of Transparent Magnesium Aluminate Spinel , 2011 .

[10]  Hongjie Wang,et al.  Synthesis of single phase β-SiAlON ceramics by reaction-bonded sintering using Si and Al2O3 as raw materials , 2011 .

[11]  Hideki Hyuga,et al.  Fabrication of Dense β‐SiAlON Ceramics with ZrO2 Additions Via a Rapid Reaction‐Bonding and Postsintering Route , 2011 .

[12]  Katsumi Yoshida,et al.  Fabrication of pressureless sintered dense β-SiAlON via a reaction-bonding route with ZrO2 addition , 2009 .

[13]  K. Hirao,et al.  Sintered Reaction‐Bonded Silicon Nitride with High Thermal Conductivity and High Strength , 2008 .

[14]  F. Riley.  Silicon Nitride and Related Materials , 2004 .

[15]  Guo‐Jun Zhang,et al.  Synthesis and Properties of Porous Single‐Phase β′‐SiAlON Ceramics , 2004 .

[16]  S. Kanzaki,et al.  Fabrication of Elongated α‐SiAlON via a Reaction‐Bonding Process , 2004 .

[17]  M. Hefetz,et al.  Effect of grain size on elastic modulus and hardness of nanocrystalline ZrO2-3 wt% Y2O3 ceramic , 2004 .

[18]  B. Lawn,et al.  Role of grain size in the strength and R-curve properties of alumina , 1990 .

[19]  T. Ekström,et al.  β‐Sialon Ceramics Prepared at 1700°C by Hot Isostatic Pressing , 1989 .

[20]  M. Nygren,et al.  Dense single-phase β-sialon ceramics by glass-encapsulated hot isostatic pressing , 1989 .

[21]  J. Briggs.  Pressureless sintering of SiAlON ceramics , 1977 .

[22]  K. Jack.  Sialons and related nitrogen ceramics , 1976 .

[23]  Randall M. German,et al.  Review: liquid phase sintering , 2009 .

[24]  I. Brown,et al.  Preparation of sialons by the nitrided pressureless sintering (NPS) technique , 1990 .

[25]  W. D. Kingery,et al.  Introduction to Ceramics , 1976 .