The effect of handle height and cart load on the initial hand forces in cart pushing and pulling

The objective of this study was to measure the three-dimensional hand forces people exert to initiate a cart push or pull for two cart loads: 73 and 181 kg, and three handle heights: knuckle, elbow, and shoulder heights. The cart used was equipped with 15.24 cm (6 in) diameter wheels. The floor was covered with carpet tiles. The laboratory-measured hand force exertions were compared to the minimum forces needed to push/pull the cart under the same conditions and to the psychophysical initial push/pull force limits. For pushing and pulling, the measured anterior-posterior hand forces were 2–2.4 times the minimum required forces. For the heavier cart load, lower forces were applied as handle height increased. Pull forces were 7% higher than push forces. The smallest vertical forces were measured at elbow height. Strength capability and gender did not have an effect on the applied forces. The mean strength percentile for the male sample was 64%, while the mean strength percentile for the female sample was 13...

[1]  Jeffrey C. Woldstad,et al.  Dynamic push and pull forces while using a manual material handling assist device , 1994 .

[2]  A. Mital,et al.  Isokinetic pull strengths in the vertical plane: effects of speed and arm angle. , 1995, Clinical biomechanics.

[3]  D B Chaffin,et al.  Validation of a biodynamic model of pushing and pulling. , 1991, Journal of biomechanics.

[4]  D. Chaffin,et al.  Lower back muscle forces in pushing and pulling. , 1989, Ergonomics.

[5]  D B Chaffin,et al.  Ergonomics guide for the assessment of human static strength. , 1975, American Industrial Hygiene Association journal.

[6]  Don B. Chaffin,et al.  Volitional Postures during Maximal Push/Pull Exertions in the Sagittal Plane , 1983 .

[7]  Don B. Chaffin,et al.  Biomechanical Computerized Simulation of Human Strength in Sagittal-Plane Activities , 1972 .

[8]  R. Jensen,et al.  Assessment of workers' compensation claims for back strains/sprains. , 1984, Journal of occupational medicine. : official publication of the Industrial Medical Association.

[9]  Shrawan Kumar,et al.  Symmetric and Asymmetric Two-Handed Pull-Push Strength of Young Adults , 1995, Hum. Factors.

[10]  D B Chaffin,et al.  Effect of handle height on lower-back loading in cart pushing and pulling. , 1991, Applied ergonomics.

[11]  A. Mital,et al.  Effects of sitting and standing, reach distance, and arm orientation on isokinetic pull strengths in the horizontal plane , 1990 .

[12]  K. H. Eberhard Kroemer.  Horizontal push and pull forces: exertable when standing in working positions on various surfaces. , 1974 .

[13]  Shrawan Kumar,et al.  Effect of body posture on isometric torque-producing capability of the back , 1991 .

[14]  Arun Garg,et al.  One-handed dynamic pulling strength with special reference to speed, handle height and angles of pulling , 1990 .

[15]  D B Chaffin,et al.  An ergonomic evaluation of handle height and load in maximal and submaximal cart pushing. , 1995, Applied ergonomics.

[16]  M. M. Ayoub,et al.  Effects of Operator Stance on Pushing and Pulling Tasks , 1974 .

[17]  Don B. Chaffin,et al.  Kinematics, Kinetics, and Psychophysical Perceptions in Symmetric and Twisting Pushing and Pulling Tasks , 1996, Hum. Factors.

[18]  Terrence John Stobbe.  The development of a practical strength testing program for industry , 1982 .

[19]  B J Daams.  Static force exertion in postures with different degrees of freedom. , 1993, Ergonomics.

[20]  S H Snook,et al.  The design of manual handling tasks: revised tables of maximum acceptable weights and forces. , 1991, Ergonomics.