Study and analysis the effect of variable applied voltage on SCIM performances based on FEA

Study and analysis the effect of variable applied voltage on SCIM performances based on FEA is presented. Three phase squirrel cage induction motor SCIM has been investigated and numerically simulated using finite element method (FEM) with the aid of ANSYS software (RMxprt and Maxwell 2D/3D). This research presents study and analysis of the effects of the voltage variation on performance and efficiency of the three-phase induction motor of the squirrel cage type. The Finite Elements Analysis Method FEA is used as one of the best methods for analysis and simulation of electrical motors in addition to the possibility of dealing with nonlinear equations, Since the induction motor is a complex electromagnetic reaction, the researchers used the ANSYS program to represent and analyze the performance of the motor under variable supply voltage. The case studied in this research is three phases, 380V, 50Hz, 2.2kW, induction motor that widely use in industrial application. The aim of this research is to study the effect of voltage variation on efficiency, current value, power factor and torque of SCIM.  The RMxprt software has been used for modeling and simulating the induction motor and calculating the values of phases currents, input and output power in additional of overall efficiency at steady state condition. The next stage of the research is creating Maxwell 2-D design from the base model of RMxprt software, Maxwell 2-D model has the ability to computing the distribution of magnetic field and explaining the performance under steady-state operation. The obtained results show significant reduction of motor performance due to the effect of variation of apply voltage.

[1]  M. H. Gmiden,et al.  Calculation of two-axis induction motor model using Finite Elements with coupled circuit , 2009, 2009 6th International Multi-Conference on Systems, Signals and Devices.

[2]  Mohammad Jahirul Islam.  Finite-element analysis of eddy currents in the form-wound multi-conductor windings of electrical machines , 2010 .

[3]  Ahmed Toumi,et al.  Magnetic Coupled Circuits Modeling of Induction Machines Oriented to Diagnostics , 2008 .

[4]  Yuji Nakasone,et al.  Engineering Analysis with ANSYS Software , 2007 .

[5]  J. Bacher,et al.  Implemented Finite Element Routines for the Calculation of Quasi-Steady and Transient Characteristics of a Squirrel Cage Induction Machine , 2008, WCE 2008.

[6]  Peter Tavner,et al.  Condition Monitoring of Rotating Electrical Machines , 2008 .

[7]  M. Rezal,et al.  Performance evaluation of multi-phase permanent magnet synchronous motor based on different winding configurations and magnetization patterns , 2019, International Journal of Power Electronics and Drive Systems (IJPEDS).

[8]  Kil To Chong,et al.  Vibration signal analysis for electrical fault detection of induction machine using neural networks , 2011, 2007 International Symposium on Information Technology Convergence (ISITC 2007).

[9]  Zhou Rui,et al.  Optimal design of single-phase induction motor based on MAXWELL 2D Rmxprt , 2010, 2010 International Conference on Electrical Machines and Systems.

[10]  S. Salimin,et al.  Comparison of different magnet arrangement on performance of flux reversal permanent magnet (FRPM) machine , 2019 .

[11]  A. Boglietti,et al.  Computational Algorithms for Induction Motor Equivalent Circuit Parameter Determination—Part II: Skin Effect and Magnetizing Characteristics , 2011, IEEE Transactions on Industrial Electronics.

[12]  Gui-Rong Liu,et al.  The Finite Element Method , 2007 .

[13]  M. García-Gracia,et al.  Cogging Torque Reduction Based on a New Pre-Slot Technique for a Small Wind Generator , 2018, Energies.

[14]  Mohamed Naceur Abdelkrim,et al.  Modeling and Simulation of Induction Motor based on Finite Element Analysis , 2016 .

[15]  M.I. Valla,et al.  A 2-D model of the induction machine: an extension of the modified winding function approach , 2004, IEEE Transactions on Energy Conversion.

[16]  Mei-shan Jin,et al.  A Maxwell 2D emulated analysis in the performance of linear introduction motor , 2010, 2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering.

[17]  Li Jingquan,et al.  Simulation analysis of the performance of linear introduction motor in Maxwell 2D , 2012, 2012 IEEE Symposium on Electrical & Electronics Engineering (EEESYM).

[18]  Thomas G. Habetler,et al.  Fault classification and fault signature production for rolling element bearings in electric machines , 2003, 4th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives, 2003. SDEMPED 2003..