Topology Optimization of an Asymmetric Elliptical Cone Subjected to Blast Loading

Abstract This paper describes a numerical procedure for the blank shape design of thin aluminum components achieved by explosive forming. The objective is to specify the initial blank shape considering the geometry of the final product. The numerical procedure consists of three steps: At first, the forming process of an asymmetric blank in an elliptical cone die cavity and without blank holder is simulated. To rectify the wrinkles without optimization the square of the primary blank will be increased. In the next step, topology optimization is employed to obtain the optimum geometry of the blank whose diameter has been increased finally, the modified blank achieved previous step is used in the new simulation to check whether or not the wrinkles mentioned in first step has been rectified. Results show the proposed numerical procedure can provide the optimal blank shape in a few iterations.

[1]  C. Loganathan,et al.  The influence of friction on the prediction of wrinkling of prestrained blanks when drawing through a conical die , 2007 .

[2]  M. S. Joun,et al.  Optimal process design in steady-state metal forming by finite element method—I. Theoretical considerations , 1993 .

[3]  Xiaoshan Lin,et al.  Finite Elements in Analysis and Design , 2011 .

[4]  Jae-Myung Lee,et al.  Blast loaded plates , 2009 .

[5]  Mohammad Habibi Parsa,et al.  Optimization of initial blank shape predicted based on inverse finite element method , 2007 .

[6]  Ravindra K. Saxena,et al.  Numerical analysis of damage for prediction of fracture initiation in deep drawing , 2011 .

[7]  ScienceDirect.  Engineering failure analysis , 1994 .

[8]  Trevor A. Dean,et al.  A review of spinning, shear forming and flow forming processes , 2003 .

[9]  Taylan Altan,et al.  Optimization of blank dimensions to reduce springback in the flexforming process , 2004 .

[10]  Thomas H. Hyde,et al.  Reminiscences from 40 years of supporting Journal of Strain Analysis for Engineering Design , 2015 .

[11]  R. Rajendran,et al.  Effective shock factors for the inelastic damage prediction of clamped plane plates subjected to non-contact underwater explosion , 2009 .

[12]  Ana Reis,et al.  The use of finite element simulation for optimization of metal forming and tool design , 2001 .

[13]  Mei Zhan,et al.  3D FEM analysis of influence of roller feed rate on forming force and quality of cone spinning , 2007 .

[14]  Prasad K. Yarlagadda,et al.  Punch Load of Non-Axisymmetric Deep Drawing Product According to Blank Shape , 2002 .

[15]  Chao Wang,et al.  Numerical simulation of failure modes of concrete gravity dams subjected to underwater explosion , 2014 .

[16]  Qin Sun,et al.  Dynamic Mechanical Behavior of 6061 Al Alloy at Elevated Temperatures and Different Strain Rates , 2013 .

[17]  H. Coules,et al.  Advanced Materials Research , 2014 .

[18]  D. Mynors,et al.  Applications and capabilities of explosive forming , 2002 .

[19]  Mohd Nasir Tamin,et al.  Estimation of Charge Mass for High Speed Forming of Circular Plates Using Energy Method , 2013 .

[20]  Paulo A.F. Martins,et al.  Strategies and limits in multi-stage single-point incremental forming , 2010 .

[21]  Abdullah A. Dhaiban,et al.  Finite element modeling and experimental results of brass elliptic cups using a new deep drawing process through conical dies , 2014 .

[22]  Salim Belouettar,et al.  A numerical method for the optimal blank shape design , 2011 .

[23]  D. R. Kumar,et al.  Optimization of initial blank shape to minimize earing in deep drawing using finite element method , 2002 .

[24]  Andrzej Rosochowski,et al.  Simulation of wrinkling in sheet metal forming , 2001 .

[25]  Anthony Turner,et al.  Materials by Design , 2008 .

[26]  Hirohiko Arai,et al.  Control of wall thickness distribution by oblique shear spinning methods , 2012 .