A review of railway sanding system research: Wheel/rail isolation, damage, and particle application

This paper reviews the academic and industrial research conducted into the practical aspects of using abrasive particles in the wheel/rail contact, such as: wheel/rail isolation, surface damage, and the application of the particles into the contact. Abrasive particles are applied to the wheel/rail contact to restore traction when low adhesion situations exist on the rail head; this process is referred to as “sanding” because sand particles are the preferred particle type in the railway industry. This aspect of sanding was covered in another sanding review. Currently, particles are applied either by firing dry particles into the wheel/rail contact via an air stream or by suspending them in a gel which can be applied using train-borne or trackside methods. The papers looked at in this review were scrutinised using a gap analysis method which grades each paper based on seven criteria, these criteria assessed: whether the papers had been peer reviewed, whether the conclusions matched the results, the range of testing scales used, and the presence of fundamental modelling work. When the findings of the research in this review were analysed, it was apparent that the negative effects of sanding (damage and isolation) have not been researched in much depth compared to its positive effects (adhesion restoration and leaf layer removal). In addition, the academic research that has been conducted has not been taken forward by industry, and industry research has not been studied in more depth by academia, suggesting a communication gap between the two branches of research; this was also the case for research into application methods.

[1]  R Lewis,et al.  Static wheel/rail contact isolation due to track contamination , 2003 .

[2]  K. Kobe.  The friction and lubrication of solids , 1951 .

[3]  Minhao Zhu,et al.  Influence of friction modifiers on improving adhesion and surface damage of wheel/rail under low adhesion conditions , 2014 .

[4]  R Lewis,et al.  Wear at the wheel/rail interface when sanding is used to increase adhesion , 2006 .

[5]  O Arias-Cuevas,et al.  Laboratory investigation of some sanding parameters to improve the adhesion in leaf-contaminated wheel—rail contacts , 2010 .

[6]  Mathieu Renouf,et al.  A new mechanical–electrical approach to the wheel-rail contact , 2006 .

[7]  O. Arias-Cuevas,et al.  Investigating the Lubricity and Electrical Insulation Caused by Sanding in Dry Wheel–Rail Contacts , 2010 .

[8]  Roger Lewis,et al.  Optimisation of a railway sanding system for optimal grain entrainment into the wheel–rail contact , 2018 .

[9]  Xin Lu,et al.  A new method for the assessment of traction enhancers and the generation of organic layers in a twin-disc machine , 2016 .

[10]  Roger Lewis,et al.  Review of top of rail friction modifier tribology , 2016 .

[11]  Zili Li,et al.  A laboratory investigation on the influence of the particle size and slip during sanding on the adhesion and wear in the wheel–rail contact , 2011 .

[12]  Zili Li,et al.  Rolling–sliding laboratory tests of friction modifiers in dry and wet wheel–rail contacts , 2010 .

[13]  P. H. Shipway.  Tribology: Friction and Wear of Engineering Materials , 1992 .

[14]  Lewis,et al.  Optimisation of a Railway Sanding System, Part 2: Adhesion Tests , 2017 .

[15]  S. Kumar,et al.  Wheel-Rail Wear and Adhesion With and Without Sand for a North American Locomotive , 1986 .

[16]  K. Gahr.  Wear by hard particles , 1998 .

[17]  R. Lewis,et al.  A review of railway sanding system research: adhesion restoration and leaf layer removal , 2018, Tribology - Materials, Surfaces & Interfaces.

[18]  R. S. Dwyer-Joyce,et al.  Disc machine study of contact isolation during railway track sanding , 2003 .

[19]  E. A. Gallardo-Hernández,et al.  Rolling–Sliding Laboratory Tests of Friction Modifiers in Leaf Contaminated Wheel–Rail Contacts , 2008 .

[20]  Fgr Zobel.  DEVELOPMENT OF REMEDIES FOR POOR ADHESION , 1975 .