Experimental and Analytical Estimation of Loss Factors by the Power Input Method

The Power Input Method (PIM) is used both experimentally and a nalytically to estimate the system loss factor for sandwich panels with various configurations of Constrained Layer Damping (CLD) treatments over a broad frequency range. The experimental power input method is applied to both uniformly and non -uniformly da mped structures. Results are compared with results from other experimental methods. A new analytical power input method is proposed for evaluating the loss factor of built -up structures, based on the finite element model with assigned properties of the con stituents. The new analytical power input method is evaluated by comparison with the commonly used Modal Strain Energy (MSE) method. Instead of making an approximate correction of the constant material properties, this analytical power input method directl y takes into account the frequency -dependent material properties of the viscoelastic material using the MSC/NASTRAN direct frequency response solution. Results of experimental and analytical methods are presented, compared and discussed. It is shown that: 1) all three currently available experimental methods yield consistent results, while the power input method gives damping estimation other than just at several discrete frequencies basically in the low frequency range; 2) both the analytical power input m ethod and the modal strain energy method yield consistent results with the experimental power input method. Furthermore, both experimental and analytical power input methods are used to investigate how loss factors change as the excitation position change. This shows another merit of the analytical power input method, because analytical modal methods cannot take into account the change of excitation position.

[1]  D. A. Bies,et al.  In situ determination of loss and coupling loss factors by the power injection method , 1980 .

[2]  M. L. Drake,et al.  Aerospace Structures Technology Damping Design Guide. Volume 2. Design Guide , 1985 .

[3]  D. J. Mead,et al.  The forced vibration of a three-layer, damped sandwich beam with arbitrary boundary conditions , 1969 .

[4]  J. Wolf,et al.  The Influence of Mounting Stiffness On Frequencies Measured In a Vibration Test , 1984 .

[5]  M. P. Norton,et al.  Some comments on the experimental determination of modal densities and loss factors for statistical energy analysis applications , 1985 .

[6]  F. H. Chu,et al.  EXPERIMENTAL DETERMINATION OF DAMPING IN MATERIALS AND STRUCTURES. , 1980 .

[7]  R. Ditaranto.  Theory of Vibratory Bending for Elastic and Viscoelastic Layered Finite-Length Beams , 1965 .

[8]  G. Lesieutre,et al.  Time Domain Modeling of Linear Viscoelasticity Using Anelastic Displacement Fields , 1995 .

[9]  Etienne Balmes,et al.  Steel/Viscoelastic/Steel Sandwich Shells Computational Methods and Experimental Validations, #167 , 2000 .

[10]  Juha Plunt.  The power injection method for vibration damping determination of body panels with applied damping treatments and trim , 1991 .

[11]  E. E. Ungar,et al.  Structure-borne sound , 1974 .

[12]  Monica Carfagni,et al.  Determining the Loss Factor by the Power Input Method (PIM), Part 1: Numerical Investigation , 1999 .

[13]  Paul Sas,et al.  An experimental-analytical SEA identification and applied validation criteria of a box type structure , 1994 .

[14]  Malcolm J. Crocker,et al.  Data processing and accuracy analysis of damping measurements , 1989 .

[15]  Frank M. Belknap.  Vibration reduction of composite structures using constrained layer damping techniques , 1991 .

[16]  George A. Lesieutre,et al.  Finite element modeling of frequency-dependent material damping using augmenting thermodynamic fields , 1990 .

[17]  Monica Carfagni,et al.  Determining the Loss Factor by the Power Input Method (PIM), Part 2: Experimental Investigation with Impact Hammer Excitation , 1999 .

[18]  Conor D. Johnson,et al.  Finite Element Prediction of Damping in Structures with Constrained Viscoelastic Layers , 1981 .

[19]  B. L. Clarkson,et al.  Frequency average loss factors of plates and shells , 1983 .

[20]  Mohan D. Rao,et al.  Measurement of damping in structures by the power input method , 2002 .

[21]  D. Mctavish,et al.  Finite element modeling of linear viscoelastic structures: The GHM method. , 1992 .

[22]  M. L. Drake,et al.  Aerospace Structures Technology Damping Design Guide. Volume 1. Technology Review , 1985 .