Effect of design parameters on performance of a top fired natural gas reformer

A three-dimensional zone method was applied to an industrial fired heater of methane steam reforming reactor. Radiation heat transfer from all gases and surfaces inside the furnace was considered. Results from previous work and data of an industrial top fired furnace were used to validate the model. A maximum temperature in external reaction tube skin was obtained at about one third of the reactor length from top in the industrial furnace. Effect of important parameters such as emissivity, extinction coefficient, heat release pattern and flame angle on performance of the fired heater are presented. It was found that decreasing the extinction coefficients of combustion gases by 25% (from about 0.20 to 0.15) caused 2.6% rise in temperature of heat sink surfaces. It was demonstrated that the three-dimensional zone method developed in this work is simple, easy and flexible for modeling and simulation of the fired heaters.

[1]  M. Pinar Mengüç,et al.  On ‘‘Radiative transfer in three-dimensional rectangular enclosures containing inhomogeneous,anisotropically scattering media’’ , 1985 .

[2]  M. V. Krishna Murthy,et al.  Modeling and simulation of a top-fired reformer , 1988 .

[3]  M. Pinar Mengüç,et al.  Thermal Radiation Heat Transfer , 2020 .

[4]  Mohamed Naceur Borjini,et al.  ANALYSIS OF RADIATIVE HEAT TRANSFER IN A PARTITIONED IDEALIZED FURNACE , 2003 .

[5]  H. C. Hottel,et al.  Radiant heat exchange in a gas-filled enclosure: Allowance for nonuniformity of gas temperature , 1958 .

[6]  R. J. Tucker,et al.  Modelling of Gas-Fired Furnaces and Boilers and Other Industrial Heating Processes , 1992 .

[7]  Tor Bjørge,et al.  Simulation of fluid flow and gaseous radiation heat transfer in a natural gas‐fired furnace , 1997 .

[8]  R. Nogay,et al.  Better design method for fired heaters , 1985 .

[9]  Michael F. Modest.  Radiative equilibrium in a rectangular enclosure bounded by gray walls , 1975 .

[10]  S. Sanaye,et al.  Thermal modeling of radiation and convection sections of primary reformer of ammonia plant , 2007 .

[11]  T. Rusten,et al.  Modelling and simulation of a steam reforming tube with furnace , 2001 .

[12]  Akbar Zamaniyan,et al.  Simulation of terrace wall methane-steam reforming reactors , 2002 .

[13]  A. Zamaniyan,et al.  Catalyst Shape as a Design Parameter—Optimum Shape for Methane-Steam Reforming Catalyst , 2002 .

[14]  Fatola Farhadi,et al.  Radiative models for the furnace side of a bottom-fired reformer , 2005 .

[15]  M. Modest.  Radiative heat transfer , 1993 .

[16]  James J. Noble,et al.  The zone method: Explicit matrix relations for total exchange areas , 1975 .

[17]  G. Froment.  Production of synthesis gas by steam- and CO2-reforming of natural gas , 2000 .

[18]  Geraldine Heynderickx,et al.  Simulation and comparison of the run length of an ethane cracking furnace with reactor tubes of circular and elliptical cross sections. , 1998 .

[19]  Jafar Towfighi,et al.  The combined simulation of heat transfer and pyrolysis reactions in industrial cracking furnaces , 2004 .

[20]  M. Murthy,et al.  Modeling Of Thermal-Radiation In Fired Heaters , 1989 .

[21]  Frank Uhlig,et al.  Numerical Algorithms with Fortran , 1996 .

[22]  R. J. Tucker.  Direct Exchange Areas for Calculating Radiation Transfer in Rectangular Furnaces , 1986 .

[23]  Benjamin T.F. Chung,et al.  A unified matrix formulation for the zone method: a stochastic approach , 1985 .