Broad-band tunable electroabsorption modulated laser for WDM application

Design and fabrication of the first 1.55-/spl mu/m wavelength tunable electroabsorption modulated laser integrated with a bent waveguide distributed-feedback (DFB) laser is reported. A low-threshold high-efficiency and stable single-longitudinal-mode operation is obtained when the electrodes of the bent DFB waveguide were uniformly pumped. In a normal configuration where the modulator part is used as an intensity modulator (i.e., AR coating on the modulator side and HR coating on the DFB side), stable single longitudinal mode output power close to 40 mW in free space is obtained with a 0-V bias to the modulator and an extinction ratio of up to 15 dB at 2.5 V. This single mode stability is due to the continuously distributed phase shift implemented in the structure thus reducing the photon pile-up inside the laser cavity as compared to an abruptly quarter-wave phase shifted DFB laser. With a nonuniform injection in the multiple electrodes, it was possible to select one particular single longitudinal mode out of the three neighboring modes inside the broad reflection band of the reflector. A wavelength tuning range of about 3.5 nm was obtained while maintaining an optical output power of more than 2 dBm from each mode. The device has a very low chirp (0.01-nm peak-to-peak) when modulated with a 2.5 Gb/s pseudorandom binary sequence (PRES) data stream and an error-free transmission over 200 km of non-DSF fiber has been demonstrated for all four wavelength channels separated by 100-GHz spacing. Also, when the modulator part of the structure is used as a phase tuning element (i.e., antireflective (AR) coating on the DFB side and HR coating on the modulator side), we have successfully demonstrated high-speed optical packet switching with a fast and wide tunable wavelength range. The optical packets can be modulated at 2.5 Gb/s and may be switched among four wavelength channels in less than one bit period.

[1]  Hirohisa Sano,et al.  Novel structure MQW electroabsorption modulator/DFB-laser integrated device fabricated by selective area MOCVD growth , 1991 .

[2]  Steven K. Korotky,et al.  Low-Loss Ti:LiNbO3 Waveguide Bends at λ = 1.3 μm , 1982, Topical Meeting on Integrated and Guided-Wave Optics.

[3]  T. Makino,et al.  Effective-index matrix analysis of distributed feedback semiconductor lasers , 1992 .

[4]  Hartmut Hillmer,et al.  Tailored DFB laser properties by individually chirped gratings using bent waveguides , 1995 .

[5]  D. Robein,et al.  Absorption-controlled tunable DFB amplifier-filters , 1994 .

[6]  T. Tanbun-Ek,et al.  Control of lasing wavelength in distributed feedback lasers by angling the active stripe with respect to the grating , 1993, IEEE Photonics Technology Letters.

[7]  B. Tromborg,et al.  Distributed feedback lasers with an S-bent waveguide for high-power single-mode operation , 1995 .

[8]  R. Linke,et al.  Modulation induced transient chirping in single frequency lasers , 1985 .

[9]  Tawee Tanbun-Ek,et al.  Integrated DFB-DBR laser modulator grown by selective area metalorganic vapor phase epitaxy growth technique , 1994 .

[10]  J. Landreau,et al.  Very high-speed wavelength switching capability Franz-Keldysh electroabsorption DFB lasers , 1996, Optical Fiber Communications, OFC..

[11]  S. Yamakoshi,et al.  Stability in single longitudinal mode operation in GaInAsP/InP phase-adjusted DFB lasers , 1987 .

[12]  Ping Zhou,et al.  Phase‐shifted distributed feedback laser with linearly chirped grating for narrow linewidth and high‐power operation , 1991 .

[13]  O. Mizuhara,et al.  Dispersion-penalty-free transmission over 130-km standard fiber using a 1.55-μm, 10-Gb/s integrated EA/DFB laser with low-extinction ratio and negative chirp , 1996, IEEE Photonics Technology Letters.