Dimensional retention of photocured ceramic units during 3D printing and sintering processes

[1]  Sefiu Abolaji Rasaki,et al.  Additive manufacturing of thin electrolyte layers via inkjet printing of highly-stable ceramic inks , 2021, Journal of Advanced Ceramics.

[2]  Yongsheng Liu,et al.  Evolution of the microstructure and mechanical properties of stereolithography formed alumina cores sintered in vacuum , 2020 .

[3]  Changyong Liu,et al.  3D printing of ceramic cellular structures for potential nuclear fusion application , 2020 .

[4]  Yusheng Shi,et al.  Preparation and biological evaluation of ZrO2 all-ceramic teeth by DLP technology , 2020, Ceramics International.

[5]  D. Fang,et al.  Dispersion and stability of SiC ceramic slurry for stereolithography , 2020 .

[6]  Yongsheng Liu,et al.  Influence of Vacuum Debinding Temperature on Microstructure and Mechanical Properties of Three-Dimensional-Printed Alumina via Stereolithography. , 2020, 3D printing and additive manufacturing.

[7]  M. Jiang,et al.  Additive manufacturing of lightweight and high-strength polymer-derived SiOC ceramics , 2020 .

[8]  Changyong Liu,et al.  Mechanical properties and microstructures of 3D printed bulk cordierite parts , 2019, Ceramics International.

[9]  Jun Ma,et al.  High mass loading ultrathick porous Li4Ti5O12 electrodes with improved areal capacity fabricated via low temperature direct writing , 2019, Electrochimica Acta.

[10]  Chengbo Liu,et al.  Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing , 2019, Ceramics International.

[11]  Gang Xu,et al.  Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics , 2019, Journal of Alloys and Compounds.

[12]  Li Yang,et al.  3D printing of ceramics: A review , 2019, Journal of the European Ceramic Society.

[13]  P. Colombo,et al.  Complex mullite structures fabricated via digital light processing of a preceramic polysiloxane with active alumina fillers , 2019, Journal of the European Ceramic Society.

[14]  M. Li,et al.  Enhancement mechanism of mechanical performance of highly porous mullite ceramics with bimodal pore structures prepared by selective laser sintering , 2019, Journal of Alloys and Compounds.

[15]  Jian Lu,et al.  Origami and 4D printing of elastomer-derived ceramic structures , 2018, Science Advances.

[16]  F. Stadler,et al.  Development and characterizations of novel aqueous-based LSCF suspensions for inkjet printing , 2018, Ceramics International.

[17]  Gang Xu,et al.  Multiple metals doped polymer-derived SiOC ceramics for 3D printing , 2018, Ceramics International.

[18]  T. Chartier,et al.  Development of a numerical simulation model for predicting the curing of ceramic systems in the stereolithography process , 2018, Journal of the European Ceramic Society.

[19]  R. Müller,et al.  New depowdering-friendly designs for three-dimensional printing of calcium phosphate bone substitutes. , 2013, Acta biomaterialia.

[20]  J. Halloran,et al.  Depth and width of cured lines in photopolymerizable ceramic suspensions , 2013 .

[21]  Sailing He,et al.  Rapid Fabrication of Complex 3D Extracellular Microenvironments by Dynamic Optical Projection Stereolithography , 2012, Advanced materials.

[22]  Jean-Pierre Kruth,et al.  Isostatic pressing assisted indirect selective laser sintering of alumina components , 2012 .

[23]  T. Chartier,et al.  Stereolithography process: Influence of the rheology of silica suspensions and of the medium on polymerization kinetics – Cured depth and width , 2012 .

[24]  Jean-Pierre Kruth,et al.  Preparation and indirect selective laser sintering of alumina/PA microspheres , 2012 .

[25]  Bin Duan,et al.  Three-dimensional nanocomposite scaffolds fabricated via selective laser sintering for bone tissue engineering. , 2010, Acta biomaterialia.

[26]  Zhangwei Chen,et al.  Curing characteristics of ceramic stereolithography for an aqueous-based silica suspension , 2010 .

[27]  J. Lewis,et al.  Concentrated hydroxyapatite inks for direct-write assembly of 3-D periodic scaffolds. , 2005, Biomaterials.

[28]  J. Lewis,et al.  Direct-write assembly of ceramics from colloidal inks , 2002 .

[29]  カニユージヤ，サトビー,et al.  Three-dimensional printing techniques , 1993 .

[30]  Tassilo Moritz,et al.  Additive Manufacturing of Ceramic Heat Exchanger: Opportunities and Limits of the Lithography-Based Ceramic Manufacturing (LCM) , 2017, Journal of Materials Engineering and Performance.

[31]  Hagedorn Yves-Christian,et al.  Net shaped high performance oxide ceramic parts by selective laser melting , 2010 .

[32]  Paul F. Jacobs,et al.  Rapid Prototyping & Manufacturing: Fundamentals of Stereolithography , 1992 .

[33]  Harris L. Marcus,et al.  Selective Laser Sintering of Ceramic Materials , 1990 .