Mechano-Chemical Surface Modification with Cu2S: Inducing Superior Lubricity

Advances toward low friction surfaces are in growing demand from many economic sectors for energy efficiency and environmental safety. However, the traditional approach of multi-grade oil formulation is limited by its inability to induce pollution-free generation of uniform oil-retaining films needed to improve surface lubricity. Here, a direct route to the formation of a surface layer of superior lubricity is presented as an alternative to the use of oil additives for friction reduction. The deformation-induced generation of a surface film consisting of low-shear-strength oil-retaining compounds is obtained via supplying chemically beneficial elements during a widely used surface finishing mechanical treatment. An ultra-low friction coefficient of about 0.01 is obtained with base oil lubrication after tailoring the surface chemistry by shot peening using a mixture of Cu2S and Al2O3; this result opens new horizons for surface engineering.

[1]  J. Greenwood,et al.  Contact of nominally flat surfaces , 1966, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[2]  R. Tenne,et al.  Fullerene‐like WS2 Nanoparticles: Superior Lubricants for Harsh Conditions , 2003 .

[3]  S. R. S. Kalpakjian.  Manufacturing Processes for Engineering Materials , 1984 .

[4]  P. H. Shipway.  Tribology: Friction and Wear of Engineering Materials , 1992 .

[5]  G. Sundararajan,et al.  Solid particle erosion behaviour of metallic materials at room and elevated temperatures , 1997 .

[6]  Peter Blau,et al.  Friction Science and Technology: From Concepts to Applications, Second Edition , 2008 .

[7]  D Dowson,et al.  Tribology: A Systems Approach to the Science and Technology of Friction, Lubrication and Wear (Tribology Series, 1) , 1978 .

[8]  W. Hirst,et al.  Surface finish and damage in sliding , 1974, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[9]  Kenneth Holmberg,et al.  Global energy consumption due to friction in passenger cars , 2012 .

[10]  Weixu Wang,et al.  Friction-reducing properties of stearic acid modification of the Cu2S film on the copper substrate , 2013 .

[11]  R. W. Carpick,et al.  Mechanisms of antiwear tribofilm growth revealed in situ by single-asperity sliding contacts , 2015, Science.

[12]  I. Etsion,et al.  Microstructure and tribological properties of Ni-based claddings on Cu substrates , 1999 .

[13]  R. Tenne,et al.  The Effect of WS2 Nanoparticles on Friction Reduction in Various Lubrication Regimes , 2004 .

[14]  F. P. Bowden,et al.  Lubrication of Metal Surfaces by Fatty Acids , 1945, Nature.

[15]  Kenneth C. Ludema,et al.  Friction Wear Lubrication: A Textbook in Tribology , 1996 .

[16]  E. Rabinowicz,et al.  Friction and Wear of Self-Lubricating Metallic Materials , 1975 .

[17]  D. Moore,et al.  Principles and Applications of Tribology , 1976 .

[18]  D. Dowson.  History of Tribology , 1979 .

[19]  J. Robinson,et al.  Direct mechanochemical cleavage of functional groups from graphene , 2015, Nature Communications.

[20]  L. Takács,et al.  Mechanochemical reaction at the interface between a metal plate and oxide powders , 2004 .

[21]  D. Wexler,et al.  Rapid reduction of copper sulfide (Cu2S) with elemental Fe and Mg using electrical discharge assisted mechanical milling (EDAMM) , 2009 .

[22]  B. Bhushan,et al.  Introduction to Tribology , 2002 .

[23]  Michael Varenberg,et al.  Towards a unified classification of wear , 2013 .