Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes

The aim of the work reported here was to utilize Taguchi methods to optimize surface finish and hole diameter accuracy in the dry drilling of Al 2024 alloy. The parameters of hole quality are analyzed under varying cutting speeds (30, 45, and 60 m/min), feed rates (0.15, 0.20, and 0.25 mm/rev), depths of drilling (15 and 25 mm), and different drilling tools (uncoated and TiN- and TiAlN-coated) with a 118° point angle. This study included dry drilling with HSS twist drills. The settings of the drilling parameters were determined by using Taguchi’s experimental design method. Orthogonal arrays of Taguchi, the signal-to-noise (S/N) ratio, the analysis of variance (ANOVA), and regression analyses are employed to find the optimal levels and to analyze the effect of the drilling parameters on surface finish and hole diameter accuracy values. Confirmation tests with the optimal levels of machining parameters are carried out in order to illustrate the effectiveness of the Taguchi optimization method. The validity of Taguchi’s approach to process optimization is well established.

[1]  Stephen A. Basile.  Modeling transverse motions of a drill bit for process understanding , 1993 .

[2]  Richard E. DeVor,et al.  Experimental investigation of the effect of drill coatings on hole quality under dry and wet drilling conditions , 2001 .

[3]  Harold R. Lindman.  Analysis of Variance in Experimental Design , 1991 .

[4]  Hong Hocheng,et al.  Taguchi analysis of delamination associated with various drill bits in drilling of composite material , 2004 .

[5]  Madhan Shridhar Phadke,et al.  Quality Engineering Using Robust Design , 1989 .

[6]  John S. Agapiou.  Design characteristics of new types of drill and evaluation of their performance drilling cast iron—I. Drill with four major cutting edges , 1993 .

[7]  M. Nouari,et al.  Experimental analysis and optimisation of tool wear in dry machining of aluminium alloys , 2003 .

[8]  Mohammed Nouari,et al.  Effect of machining parameters and coating on wear mechanisms in dry drilling of aluminium alloys , 2005 .

[9]  Walter W. Olson,et al.  An experimental study of cutting fluid effects in drilling , 1997 .

[10]  M. Cotterell,et al.  Minimal lubrication machining of aluminium alloys , 2002 .

[11]  Y. S. Tarng,et al.  Design optimization of cutting parameters for turning operations based on the Taguchi method , 1998 .

[12]  Ismail Lazoglu,et al.  Forces and hole quality in drilling , 2005 .

[13]  Hualin Zhao.  Predictive models for forces, power and hole oversize in drilling operations , 1994 .

[14]  C. Tsao,et al.  Cutting performance of different coated twist drills , 1999 .

[15]  R. J. Furness,et al.  Statistical Analysis of the Effects of Feed, Speed, and Wear on Hole Quality in Drilling , 1996 .

[16]  Eyup Bagci,et al.  A study of Taguchi optimization method for identifying optimum surface roughness in CNC face milling of cobalt-based alloy (stellite 6) , 2006 .

[17]  T. R. Bement,et al.  Taguchi techniques for quality engineering , 1995 .

[18]  Jean M. Dasch,et al.  A comparison of five categories of carbon-based tool coatings for dry drilling of aluminum , 2006 .

[19]  George Epstein,et al.  Making data analysis easier. , 2007, Behavioral healthcare.

[20]  J. Ni,et al.  The effects of thermal distortions on the diameter and cylindricity of dry drilled holes , 2001 .