Focused ion beam-shaped microtools for ultra-precision machining of cylindrical components

Abstract Focused ion beam (FIB) sputtering is used to shape a variety of cutting tools with dimensions in the 15–100 μm range and cutting edge radii of curvature of 40 nm. The shape of each microtool is controlled to a pre-specified geometry that includes rake and relief features. We demonstrate tools having rectangular, triangular, and other complex-shaped face designs. A double-triangle tip on one tool is unique and demonstrates the versatility of the fabrication process. The FIB technique allows observation of the tool during fabrication, and, thus, reproducible features are generated with sub-micron precision. Tools are made from tungsten carbide, high-speed tool steel, and single crystal diamond. Application of FIB-shaped tools in ultra-precision microgrooving tests shows that the cross-section of a machined groove is an excellent replication of the microtool face. Microgrooves on 40–150 μm pitch are cut into 3 mm diameter polymer rods, for groove arc lengths greater than 12 cm. The surface finish of machined features is also reported; groove roughness (Ra) is typically less than 0.2 μm. Ultra-precision machining of cylindrical substrates is extended to make bound metal microcoils having feature sizes of 20–40 μm.

[1]  Craig R. Friedrich,et al.  Micromilling development and applications for microfabrication , 1997 .

[2]  George M. Whitesides,et al.  Microorigami: Fabrication of Small, Three-Dimensional, Metallic Structures , 2001 .

[3]  P. Russell,et al.  Chemically and geometrically enhanced focused ion beam micromachining , 1998 .

[4]  Henry Guckel,et al.  High winding density micro coils for magnetic actuators , 1998 .

[5]  K. Baberschke,et al.  High‐sensitivity broadband microwave spectroscopy with small nonresonant coils , 1986 .

[6]  G. L. Benavides,et al.  Micromilling of metal alloys with focused ion beam–fabricated tools , 1999 .

[7]  G. Carter.  The effects of surface ripples on sputtering erosion rates and secondary ion emission yields , 1999 .

[8]  P. McNally,et al.  A comparative study of Pd/Sn/Au, Au/Ge/Au/Ni/Au, Au-Ge/Ni and Ni/Au-Ge/Ni ohmic contacts to n-GaAs , 1998 .

[9]  Takeshi Yoneyama,et al.  Micro cutting in the micro lathe turning system , 1999 .

[10]  R. Read,et al.  New Technology and Novel Design make SubMicron Production Practical , 2000 .

[11]  C. R. Friedrich,et al.  The micromilling process for high aspect ratio microstructures , 1996 .

[12]  George M. Whitesides,et al.  Constructing single- and multiple-helical microcoils and characterizing their performance as components of microinductors and microelectromagnets , 1997 .

[13]  Jon Orloff,et al.  High‐resolution focused ion beams , 1993 .

[14]  D. Adams,et al.  Microgrooving and microthreading tools for fabricating curvilinear features , 2000 .

[15]  H. Weule,et al.  Micro-Cutting of Steel to Meet New Requirements in Miniaturization , 2001 .

[16]  Henry Guckel,et al.  An electromagnetic micro dynamometer , 1995, Proceedings IEEE Micro Electro Mechanical Systems. 1995.

[17]  Andrew G. Webb,et al.  Radiofrequency microcoils in magnetic resonance , 1997 .

[18]  Lothar Bohn,et al.  Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills , 1999 .

[19]  Craig R. Friedrich,et al.  Micrometer-scale machining: tool fabrication and initial results , 1996 .

[20]  M. Boman,et al.  Rapid Prototyping of Functional Three-Dimensional Microsolenoids and Electromagnets by High-Pressure Laser Chemical Vapor Deposition , 1998 .

[21]  R. M. Bradley,et al.  Theory of ripple topography induced by ion bombardment , 1988 .

[22]  Okazaki,et al.  NC micro-lathe to machine micro-parts , 2000 .

[23]  Michael J. Vasile,et al.  MICROFABRICATION BY ION MILLING : THE LATHE TECHNIQUE , 1994 .

[24]  Jackman,et al.  Design and fabrication of topologically complex, three-dimensional microstructures , 1998, Science.

[25]  C. Giaconia,et al.  Technologies for the fabrication of cylindrical fine line devices , 1997 .

[26]  R. Joshi,et al.  A dual damascene hard metal capped Cu and Al-alloy for interconnect wiring of ULSI circuits , 1993, Proceedings of IEEE International Electron Devices Meeting.

[27]  L. R. Harriott,et al.  A Second Generation Focused Ion Beam Micromachining System , 1987, Advanced Lithography.

[28]  D. Adams,et al.  FOCUSED ION BEAM SHAPED MICRO-CUTTING TOOLS FOR FABRICATING CURVILINEAR FEATURES , 2022 .

[29]  C. Speake,et al.  Photolithographic manufacture of a superconducting levitation coil on a spherical substrate , 2000 .