Metal mesh materials have been used successfully in vibration isolators and bearing dampers due to their superior friction or hysteresis damping mechanism. These materials are formed to metal mesh (or wire mesh) structures in ring-shape by compressing a weave of metal wires, in general. Recently, oil-free rotating machinery implement metal mesh structures into hydrodynamic gas foil bearings by replacing bump strip layers with them, to increase its bearing structural damping. A metal mesh foil bearing (MMFB) consists of a top foil and support elastic metal mesh pads installed between a rotating shaft and a housing. The present research presents load capacity tests of a MMFB at rotor rest (0 rpm) and 30 krpm for three metal mesh densities of 13.1%, 23.2%, and 31.6%. The metal mesh pad of test MMFB is made using a stainless steel wire with a diameter of 0.15 mm. Test rig comprises a rigid rotor with a diameter of 60 mm supported on two ball bearings at both ends and test MMFB with an axial length of 50 mm floats on the rotor. Static loads is provided with a mechanical loading device on test MMFB and a strain gauge type load cell measures the applied static loads. A series of static load versus deflection tests were conducted for selected metal mesh densities at rest (0 rpm). Test data are compared to further test results of static load versus journal eccentricity recorded at the rotor speed of 30 krpm. Test data show a strong nonlinearity of bearing deflection (journal eccentricity) with static load, independent of rotor spinning. Observed hysteresis loops imply significant structural damping of test MMFB. Measured journal deflections at 0 rpm are in similar trend to recorded journal eccentricities at the finite rotor speed; thus implying that the MMFB performance depends mainly on the metal mesh structures. The paper also estimates linearlized stiffness coefficient and damping loss factor of test MMFB using the measured static load versus deflection test data at 0 rpm and 30 krpm. The results show that the highest mesh density of 31.6% produces highest linearlized stiffness coefficient and damping loss factor. With rotor spinning at 30 krpm, the linearlized stiffness coefficient and damping loss factor decrease slightly, independent of metal mesh densities. The present test data will serve as a database for benchmarking MMFB predictive models.
[1]
John M. Vance,et al.
Design Equations for Wire Mesh Bearing Dampers in Turbomachinery
,
2005
.
[2]
J. M. Vance,et al.
Cryogenic Temperature Effects on Metal Mesh Dampers and Liquid Hydrogen Turbopump Rotordynamics
,
2002
.
[3]
Jerry H. Ginsberg,et al.
Mechanical and Structural Vibrations: Theory and Applications
,
2001
.
[4]
Huageng Luo,et al.
Dynamic Characteristics of Shape Memory Alloy Metal Mesh Dampers
,
2009
.
[5]
Vivek Vaibhav Choudhry.
Experimental evaluation of wire mesh for design as a bearing damper
,
2004
.
[6]
Luis San Andrés,et al.
Measurement of Structural Stiffness and Damping Coefficients in a Metal Mesh Foil Bearing
,
2009
.
[7]
John M. Vance,et al.
Rotordynamic Bearing Dampers for Cryogenic Rocket Engine Turbopumps
,
2003
.
[8]
Huageng Luo,et al.
Nonlinear Dynamic Characterization of Oil-Free Wire Mesh Dampers
,
2008
.
[9]
Eyad Mohammad Al-Khateeb.
Design, modeling and experimental investigation of wire mesh vibration dampers
,
2002
.
[10]
John M. Vance,et al.
Experimental Evaluation of a Metal Mesh Bearing Damper
,
2000
.
[11]
John M. Vance,et al.
Experimental Evaluation of a Metal Mesh Bearing Damper in Parallel With a Structural Support
,
2001
.
[12]
Luis San Andrés,et al.
Identification of Rotordynamic Force Coefficients of a Metal Mesh Foil Bearing Using Impact Load Excitations
,
2010
.
[13]
Wei Wei,et al.
Study on the damping characteristics of MR damper in flexible supporting of turbo-pump rotor for engine
,
2006,
2006 1st International Symposium on Systems and Control in Aerospace and Astronautics.
[14]
John M. Vance,et al.
Effect of Static and Dynamic Misalignment on Ball Bearing Radial Stiffness
,
2004
.
[15]
Luis San Andrés,et al.
Measurements of Drag Torque, Lift-Off Journal Speed, and Temperature in a Metal Mesh Foil Bearing
,
2009
.