X-ray ultramicroscopy: A new method for observation and measurement of filler dispersion in thermoplastic composites

A phase contrast X-ray imaging technique has been developed to observe and determine filler distribution in polymer composites, providing greatly enhanced 2-D image quality over conventional methods such as scanning electron microscopy (SEM). High spatial resolution X-ray ultramicroscopy (XuM) was developed and employed for this work. This method provides a clear visualization of filler dispersion patterns in polypropylene and nylon 6 matrices even with a sample thickness of up to 200 μm. Quantitative analysis of the filler dispersion quality derived from the 2-D images was carried out using a commercially available image analysis software. The X-ray phase contrast imaging and micro-tomography results presented in this paper demonstrate the viability of these techniques for qualitative and quantitative characterizations of filler distribution in thermoplastic composites. This technique offers several advantages over existing imaging methods because it avoids tedious sample preparation, yields well contrasted image enabling more accurate quantification of composite microstructure, and provides 2-D and 3-D information on filler distribution in polymer composites.

[1]  C. Nah,et al.  Properties of natural rubber composites reinforced with silica or carbon black: influence of cure accelerator content and filler dispersion , 2003 .

[2]  Y. Suetsugu.  State of Dispersion – Mechanical Properties Correlation in Small Particle Filled Polymer Composites , 1990 .

[3]  Sandrine Marceau,et al.  Reinforcement effects in fractal-structure-filled rubber , 2002 .

[4]  B. B. Boonstra,et al.  Effect of Carbon Black Dispersion on the Mechanical Properties of Rubber Vulcanizates , 1963 .

[5]  P. Lafleur,et al.  Effect of filler dispersion on polypropylene morphology , 2004 .

[6]  Benoit B. Mandelbrot,et al.  Fractal Geometry of Nature , 1984 .

[7]  Joy P. Dunkers,et al.  The application of optical coherence tomography to problems in polymer matrix composites , 2001 .

[8]  T. Takeda.  Phase-contrast and fluorescent X-ray imaging for biomedical researches , 2005 .

[9]  L. Bokobza,et al.  Atomic force microscopy investigation of filled elastomers and comparison with transmission electron microscopy — application to silica-filled silicone elastomers , 2001 .

[10]  S. Bastide,et al.  Mechanical behaviour of polypropylene composites containing fine mineral filler: Effect of filler surface treatment , 1998 .

[11]  L. Avérous,et al.  Determination of the microtexture of reinforced thermoplastics by image analysis , 1998 .

[12]  A Tewari,et al.  Efficient estimation of number density in opaque material microstructures: the large‐area disector , 2000, Journal of microscopy.

[13]  A. Gokhale,et al.  Visualization of three-dimensional microstructures , 2005 .

[14]  Y. Wang,et al.  Single screw extrusion compounding of particulate filled thermoplastics: State of dispersion and its influence on impact properties , 1996 .

[15]  S. Wilkins,et al.  Quantitative X‐ray projection microscopy: phase‐contrast and multi‐spectral imaging , 2002, Journal of microscopy.

[16]  F Rustichelli,et al.  Phase-contrast imaging of thin biomaterials. , 2001, Biomaterials.

[17]  R. Vaia,et al.  X‐ray powder diffraction of polymer/layered silicate nanocomposites: Model and practice , 2002 .

[18]  T. Kyu,et al.  An experimental technique for characterizing dispersion in compounds of particulates in thermoplastics using small-angle light scattering , 1990 .

[19]  S. Lynch,et al.  Dispersion assessment of flame retardant filler/polymer systems using a combination of X-ray mapping and multifractal analysis , 2002 .

[20]  L. Leibler,et al.  Analysis of polymer blend morphologies from transmission electron micrographs , 2005 .

[21]  Jensen,et al.  Erratum: Fractal measures and their singularities: The characterization of strange sets , 1986, Physical review. A, General physics.

[22]  Richard H. Bossi,et al.  Composite structure development decisions using X-ray CT measurements , 1995 .

[23]  A. Bhowmick,et al.  New insights into rubber–clay nanocomposites by AFM imaging , 2006 .

[24]  A. Gokhale,et al.  Estimation of three-dimensional grain size distribution from microstructural serial sections , 2001 .

[25]  V. Causin,et al.  Assessing organo-clay dispersion in polymer layered silicate nanocomposites: A SAXS approach , 2005 .

[26]  J. M. Adams,et al.  Factors affecting the impact properties of mineral filled polypropylene , 1990 .

[27]  Peter Cloetens,et al.  A study of fracture of unidirectional composites using in situ high-resolution synchrotron X-ray microtomography , 2006 .

[28]  D Stoyan,et al.  Statistical characterization of TEM images of silica‐filled rubber , 2005, Journal of microscopy.

[29]  Paolo Ermanni,et al.  Micro-computed tomography determination of glass fibre reinforced polymer meso structure , 2006 .

[30]  Joseph Kuruvilla,et al.  Mechanical properties of titanium dioxide-filled polystyrene microcomposites , 2004 .

[31]  M. Osman,et al.  Interparticle and particle-matrix interactions in polyethylene reinforcement and viscoelasticity , 2005 .

[32]  S. Wilkins,et al.  X-ray phase-contrast microscopy and microtomography. , 2003, Optics express.

[33]  A. Gokhale,et al.  Effect of gravity on three-dimensional coordination number distribution in liquid phase sintered microstructures , 1999 .

[34]  B. Haworth,et al.  Polyethylene compounds containing mineral fillers modified by acid coatings. 1: Characterization and processing , 2000 .

[35]  John C. Russ,et al.  The Image Processing Handbook , 2016, Microscopy and Microanalysis.

[36]  M. Cakmak,et al.  The role of plasticizer on the exfoliation and dispersion and fracture behavior of clay particles in PVC matrix: a comprehensive morphological study , 2004 .

[37]  Ralph Müller,et al.  The Zürich Experience: One Decade of Three-Dimensional High-Resolution Computed Tomography , 2002, Topics in magnetic resonance imaging : TMRI.