Passive balancing of the DC bus midpoint for Neutral Point Clamped (NPC) based Voltage Source Converters

This paper presents a passive method to balance the voltage of the split capacitors in Neutral Point Clamped (NPC) based Voltage Source Converters (VSC). The voltage of the two capacitors is equated by connecting a low VA transformer at the AC side of the converter. The transformer is connected in wye configuration and its neutral point is connected to the DC side midpoint through a resistance and an inductance. By doing so, it is assured that the mean voltages of the DC side capacitors are balanced. In addition, this method is independent to the load and therefore the balancing is assured under any working point of the converter. The VSC and the balancing circuit have been simulated in the simulation tool Saber and the good performance of the balancing circuit has been validated experimentally in a 6.7KVA test bench.

[1]  Kwanghee Nam,et al.  A DC-link voltage balancing algorithm for 3-level converter using the zero sequence current , 1999, 30th Annual IEEE Power Electronics Specialists Conference. Record. (Cat. No.99CH36321).

[2]  Andrew Cross,et al.  Chain-link based HVDC Voltage Source Converter using current injection , 2010 .

[3]  H. P. Mohammadi,et al.  A Transformerless Medium-Voltage STATCOM Topology Based on Extended Modular Multilevel Converters , 2011, IEEE Transactions on Power Electronics.

[4]  J. Chivite-Zabalza,et al.  Novel Zero-Sequence Blocking Transformer (ZSBT) Using Three Single-Phase Transformers , 2013, IEEE Transactions on Energy Conversion.

[5]  H. Akagi,et al.  Voltage Balancing Control for a Three-Level Diode-Clamped Converter in a Medium-Voltage Transformerless Hybrid Active Filter , 2009, IEEE Transactions on Power Electronics.

[6]  Zhongdong Yin,et al.  Zero-sequence harmonics current minimization using zero-blocking reactor and Zig-Zag transformer , 2008, 2008 Third International Conference on Electric Utility Deregulation and Restructuring and Power Technologies.

[7]  Bin Wu,et al.  Multilevel Voltage-Source-Converter Topologies for Industrial Medium-Voltage Drives , 2007, IEEE Transactions on Industrial Electronics.

[8]  S R Pulikanti,et al.  Voltage Balancing Control of Three-Level Active NPC Converter Using SHE-PWM , 2011, IEEE Transactions on Power Delivery.

[9]  Vijay Srinivasan,et al.  Modeling and design of a neutral-point voltage regulator for a three-level diode-clamped inverter using multiple-carrier modulation , 2006, IEEE Transactions on Industrial Electronics.

[10]  A.M. Hava,et al.  A novel neutral point potential stabilization technique using the information of output current polarities and voltage vector , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[11]  Yongdong Li,et al.  Analysis and Calculation of Zero-Sequence Voltage Considering Neutral-Point Potential Balancing in Three-Level NPC Converters , 2010, IEEE Transactions on Industrial Electronics.

[12]  Bin Wu,et al.  Powering the Future of Industry: High-Power Adjustable Speed Drive Topologies , 2012, IEEE Industry Applications Magazine.

[13]  N. Mohan,et al.  Analysis of a new power electronics interface with approximately sinusoidal 3-phase utility currents and a regulated DC output , 1992 .

[14]  M. A. Rodriguez,et al.  Power quality analysis of a static synchronous compensator (STATCOM) connected to a high voltage transmission network , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.

[15]  Holmes,et al.  Pulse width modulation for power converters , 2003 .

[16]  Gonzalo Abad,et al.  Medium Voltage–High Power Converter Topologies Comparison Procedure, for a 6.6 kV Drive Application Using 4.5 kV IGBT Modules , 2012, IEEE Transactions on Industrial Electronics.

[17]  Jie Chen,et al.  Multilevel SVPWM With DC-Link Capacitor Voltage Balancing Control for Diode-Clamped Multilevel Converter Based STATCOM , 2013, IEEE Transactions on Industrial Electronics.

[18]  A.K. Gupta,et al.  A Simple Space Vector PWM Scheme to Operate a Three-Level NPC Inverter at High Modulation Index Including Overmodulation Region, With Neutral Point Balancing , 2007, IEEE Transactions on Industry Applications.

[19]  Javier Chivite-Zabalza,et al.  A Large-Power Voltage Source Converter for FACTS Applications Combining Three-Level Neutral-Point-Clamped Power Electronic Building Blocks , 2013, IEEE Transactions on Industrial Electronics.

[20]  M. A. Rodriguez,et al.  Voltage balancing control in 3-Level Neutral-Point Clamped inverters using triangular carrier PWM modulation for FACTS applications , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.

[21]  Bin Wu,et al.  Recent Advances and Industrial Applications of Multilevel Converters , 2010, IEEE Transactions on Industrial Electronics.

[22]  Gonzalo Abad,et al.  Modular Multilevel Converter With Different Submodule Concepts—Part I: Capacitor Voltage Balancing Method , 2013, IEEE Transactions on Industrial Electronics.

[23]  M.A. Rodriguez,et al.  Design, analysis and comparison of multilevel topologies for DSTATCOM applications , 2005, 2005 European Conference on Power Electronics and Applications.

[24]  Wensheng Song,et al.  A Carrier-Based PWM Strategy With the Offset Voltage Injection for Single-Phase Three-Level Neutral-Point-Clamped Converters , 2013, IEEE Transactions on Power Electronics.

[25]  A. Cross,et al.  A high-power-factor, three-phase isolated AC-DC converter using high-frequency current injection , 2003 .

[26]  Ashwin M. Khambadkone,et al.  A simple space vector PWM scheme to operate a three-level NPC inverter at high modulation index including over-modulation region, with neutral point balancing , 2005 .