Effect of Combined Tempering and Aging in the Austenite Reversion, Precipitation, and Tensile Properties of an Additively Manufactured Maraging 300 Steel

[1]  A. Jardini,et al.  Investigation of Building Orientation and Aging on Strength–Stiffness Performance of Additively Manufactured Maraging Steel , 2021, Journal of Materials Engineering and Performance.

[2]  D. Rosen,et al.  A characterization method for mechanical properties of metal powder bed fusion parts , 2020, The International Journal of Advanced Manufacturing Technology.

[3]  A. Jardini,et al.  Austenite reversion kinetics and stability during tempering of an additively manufactured maraging 300 steel , 2019, Additive Manufacturing.

[4]  H. Liao,et al.  Additive manufacturing of WC reinforced maraging steel 300 composites by cold spraying and selective laser melting , 2019, Surface and Coatings Technology.

[5]  A. Sukhikh,et al.  Austenite in Nanostructured Maraging Steel , 2019, Inorganic Materials: Applied Research.

[6]  A. Jardini,et al.  Effect of thermal cycling and aging stages on the microstructure and bending strength of a selective laser melted 300-grade maraging steel , 2019, Materials Science and Engineering: A.

[7]  K. Al-Rubaie,et al.  Precipitation in 300 grade maraging steel built by selective laser melting: Aging at 510 °C for 2 h , 2019, Materials Characterization.

[8]  R. Raghavendra,et al.  Process phenomena influencing the tensile and anisotropic characteristics of additively manufactured maraging steel , 2019, Materials Science and Engineering: A.

[9]  S. Seils,et al.  Fundamentals of Isothermal Austenite Reversion in a Ti-Stabilized 12cr - 6 Ni - 2 Mo Super Martensitic Stainless Steels: Thermodynamics Versus Experimental Assessments , 2019, SSRN Electronic Journal.

[10]  Aaas News,et al.  Book Reviews , 1893, Buffalo Medical and Surgical Journal.

[11]  A. Sukhikh,et al.  Properties of Austenite in Maraging Steel , 2018, Solid State Phenomena.

[12]  Bo Chen,et al.  Influence of processing parameters and heat treatment on the mechanical properties of 18Ni300 manufactured by laser based directed energy deposition , 2018, Optics & Laser Technology.

[13]  F. Niessen.  Austenite reversion in low-carbon martensitic stainless steels – a CALPHAD-assisted review , 2018 .

[14]  Xianguang Zhang,et al.  Orientation of austenite reverted from martensite in Fe-2Mn-1.5Si-0.3C alloy , 2018 .

[15]  Min Liu,et al.  Microstructural evolution, nanoprecipitation behavior and mechanical properties of selective laser melted high-performance grade 300 maraging steel , 2017 .

[16]  Leonardo Wu,et al.  Austenite reversion kinetics and stability during tempering of a Ti-stabilized supermartensitic stainless steel: Correlative in situ synchrotron x-ray diffraction and dilatometry , 2017 .

[17]  A. Tuissi,et al.  Aging Behaviour and Mechanical Performance of 18-Ni 300 Steel Processed by Selective Laser Melting , 2016 .

[18]  C. Tasan,et al.  Spectral TRIP enables ductile 1.1 GPa martensite , 2016 .

[19]  Andrew T. Anderson,et al.  Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones , 2015, 1512.02593.

[20]  Ulrich Amsel,et al.  Standard Guide For Preparation Of Metallographic Specimens , 2016 .

[21]  V. Dementyev,et al.  On problem of increasing the structural strength of maraging steels , 2015, Inorganic Materials: Applied Research.

[22]  C. Tasan,et al.  Nanolaminate Transformation-Induced Plasticity-Twinning-Induced Plasticity steel with Dynamic Strain Partitioning and Enhanced damage Resistance , 2015 .

[23]  Antonio Domenico Ludovico,et al.  Experimental investigation and statistical optimisation of the selective laser melting process of a maraging steel , 2015 .

[24]  C. Tasan,et al.  Smaller is less stable: Size effects on twinning vs. transformation of reverted austenite in TRIP-maraging steels , 2014 .

[25]  D. Ponge,et al.  Designing Heusler nanoprecipitates by elastic misfit stabilization in Fe–Mn maraging steels , 2014 .

[26]  M. Herbig,et al.  Segregation engineering enables nanoscale martensite to austenite phase transformation at grain boun , 2013 .

[27]  D. Ponge,et al.  Chemical gradients across phase boundaries between martensite and austenite in steel studied by atom probe tomography and simulation , 2014, 1402.0232.

[28]  Jean-Pierre Kruth,et al.  Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel , 2011 .

[29]  D. Ponge,et al.  Designing Ultrahigh Strength Steels with Good Ductility by Combining Transformation Induced Plasticity and Martensite Aging , 2009 .

[30]  D. Ponge,et al.  Nanoprecipitate-hardened 1.5 GPa steels with unexpected high ductility , 2009 .

[31]  U. Viswanathan,et al.  Effects of austenite reversion during overageing on the mechanical properties of 18 Ni (350) maraging steel , 2005 .

[32]  P. Scardi,et al.  Whole powder pattern modelling. , 2002, Acta crystallographica. Section A, Foundations of crystallography.

[33]  T. Kutty,et al.  Dilatometric technique for evaluation of the kinetics of solid-state transformation of maraging steel , 1993, Metallurgical and Materials Transactions A.

[34]  U. Viswanathan,et al.  Precipitation hardening in 350 grade maraging steel , 1993, Metallurgical and Materials Transactions A.

[35]  A. Ardell,et al.  Precipitation hardening , 1985 .

[36]  Robert E. Reed-Hill,et al.  Physical Metallurgy Principles , 1972 .

[37]  Standard Test Methods for Tension Testing of Metallic Materials 1 , 2022 .