An integrated acoustic–mechanical development method for off-road motorcycle silencers: from design to sound quality test

Vehicle noise is one of the main sources of complaints because it is widespread and active in almost all environments, from urban areas to rural context. The present work aims to describe a practical procedure to design silencers for off-road motorcycles so that, once produced, they are lightweight, do not affect the engine performances and cut noise emissions to a sustainable limit. The required noise reduction, usually around 35–40 dB, can be achieved only by carefully designing the exhaust system. The first part of the paper provides the theoretical background of noise propagation in ducts, describes the main attenuation devices as tools the designer can use in the development process and outlines the workflow. In the second part, a case study of silencer optimization is presented: the noise emitted by a real off-road motorcycle is characterized and, once the sound pressure level and the mass flow generated by the engine are known, a silencer fulfilling noise attenuation, size and pressure drop requirements is designed, 3D-modeled and rendered. The outcome of the acoustic design process can be used to perform virtual sound quality tests, which can be of interest for manufacturers to catch the attention of passionate users.

[1]  Barbara Motyl,et al.  An eco-innovation and technical contaminated approach for designing a low environmental impact off-road motorcycle , 2018 .

[2]  Gabriella Cerrato Jay,et al.  Sound/Vibration Quality Engineering Part 1 - Introduction and the SVQ Engineering Process , 2007 .

[3]  A. Cummings,et al.  Sound attenuation of a finite length dissipative flow duct silencer with internal mean flow in the absorbent , 1988 .

[4]  Bo Xu,et al.  Integrating BIM and augmented reality for interactive architectural visualisation , 2014 .

[5]  Imad Alsyouf,et al.  Implementing product design development methodology for assessing and improving the performance of products , 2015 .

[6]  G. Sequenzia,et al.  An advanced multibody model for evaluating rider’s influence on motorcycle dynamics , 2015 .

[7]  Ming Une Jen,et al.  Target setting for enhancing sound quality of a motorcycle by sound systhesis technique , 2016 .

[8]  Casey L. Brown,et al.  Detection and Classification of Motor Vehicle Noise in a Forested Landscape , 2013, Environmental Management.

[9]  G. Pietila,et al.  Evaluation of Different Vehicle Noise Reduction Test Methods for Tire Sound Quality Synthesis , 2007 .

[10]  Fabrizio Argenti,et al.  Simulation and design of active control systems for acoustic pulse noise , 2018 .

[11]  Xavier Fischer,et al.  Multidisciplinary design process based on virtual prototyping for microsystem design , 2010 .

[12]  W H Close,et al.  VEHICLE NOISE SOURCES AND NOISE-SUPPRESSION POTENTIAL , 1975 .

[13]  Antonis A. Argyros,et al.  Hobbit , a care robot supporting independent living at home : First prototype and lessons learned , 2015 .

[14]  Thomas D. Durbin,et al.  IN-USE ACTIVITY MEASUREMENTS FOR OFF-ROAD MOTORCYCLES AND ALL-TERRAIN VEHICLES , 2004 .

[15]  D. Goossens,et al.  Dust emission by off-road driving: Experiments on 17 arid soil types, Nevada, USA , 2009 .

[16]  A. J. Peterson,et al.  Fuel Effects Study with In-Use Two-Stroke Motorcycles and All-Terrain-Vehicles , 2013 .

[17]  B. Muller.  Mending man's ways: Wickedness, complexity and off-road travel , 2016 .

[18]  Miao Xiao-dong,et al.  Analysis of whole body noise and muffler improvement for a motorcycle , 2011 .

[19]  Julia A. Jones,et al.  Road Ecology: Science and Solutions , 2002 .

[20]  W. Sheate,et al.  Sustainable management of recreational off-road vehicles in National Parks in the UK. , 2001 .

[21]  Robert Kreuzbauer,et al.  Embodied Cognition and New Product Design: Changing Product Form to Influence Brand Categorization , 2005 .

[22]  Thomas Bäuml.  Modelling, simulation and validation of an electrical zero emission off-road motorcycle , 2010 .

[23]  Weam S. Elsahar,et al.  Measurement and Simulation of Two-Inlet Single-Outlet Mufflers , 2015 .

[24]  Frédéric Merienne,et al.  Human factors consideration in the interaction process with virtual environment , 2010 .

[25]  Kazuhiko Tanaka,et al.  Design Method of Motorcycle Exhaust Sound Fitting to Vehicle Concept Regardless of Engine Configurations , 2014 .

[26]  R. Barbagallo,et al.  Interactive re-design of a novel variable geometry bicycle saddle to prevent neurological pathologies , 2016 .

[27]  Ali Belhocine,et al.  Predictive modeling and simulation of the structural contact problems between the brake pads and rotor in frictional sliding contact , 2018 .

[28]  Mats Åbom,et al.  SIDLAB : New 1D sound propagation simulation software for complex duct networks , 2006 .

[29]  R. Barbagallo,et al.  Redesign and multibody simulation of a motorcycle rear suspension with eccentric mechanism , 2018 .

[30]  Giuseppe Di Gironimo,et al.  Virtual concepts and experiments to improve quality of train interiors , 2009 .

[31]  Tamer Elnady,et al.  Investigation of the Acoustic Performance of After Treatment Devices , 2011 .

[32]  Ekaitz Zulueta,et al.  Towards a methodology to build virtual reality manufacturing systems based on free open software technologies , 2016, International Journal on Interactive Design and Manufacturing (IJIDeM).

[33]  Xavier Fischer,et al.  Research in Interactive Design: Virtual, Interactive and Integrated Product Design and Manufacturing for Industrial Innovation , 2010 .